At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hey all Trying to understand how to properly build a basic bluetooth example without errors using zephyr between the 2 cores Error: manually cleaning and flashing reading...
Hello,
I use this code for system_off on a nrf52840 custom board. const struct device *button = device_get_binding("GPIO_0"); gpio_pin_interrupt_configure(button, SW0_GPIO_PIN...
nRF52840 Dongle is configured as Sniffer in the right way according to documentation. When sniffing capture on Wireshark is started, only the Advertising packets are captured...
I have a project where I use the nrf9160dk as a gateway between a BLE sensor and LTE.
The hci_lpuart sample is flashed tonrf9160dk_nrf52840 and the nrf9160dk_nrf9160_ns...
I got a Segger J-Link EDU to be use to program my Nordic Thingy 91. I have previously program the device via USB using the NRF Connect Desktop :Programmer. But connecting...
Hello everyone,
I am having an odd problem. I am using an SoC based on the nRF52832 (the ISP1507-AX). I am using ncs v1.7.0 for development. I am trying out a few things...
Hello guys,
I would like to work using nRF52 as my processor to create products in the future, but I heard about Specific Absorption Rate (SAR) testing and that is good...
Hi all, I am a little confused by the requirements for the external GPS antennal options. My board is version 1.0.1.
In this page ( https://devzone.nordicsemi.com/nordic...
The project I'm using the peripheral BLE UART that has been modified to use freeRTOS and PWM.
I'm using two channel PWM to drive a resonance motor at 25.6 kHz. If I disable...
Dear
First of all, I am so sorry because of my english skill.
I got NRF_ERROR_RESOURCES when the connection between NRF Module and mobile device is disconnected due to...
I want to start the most basic hello world project on my nrf9160 thingy development board but am having trouble building my own custom project or any of the sample ones provided...
Question on an older chip:
Can anyone tell me if FW originally written for the nRF24LE1E would be completely compatible with the nRF24LE1G? I have an opportunity to source...
Hi,
Device: NRF53
I'm trying to send 3 notify packets in a 15ms connection internal but I can send 2.
I'm using Nrf connect and Zephyr. is there a limit or a define...
I seem to be having weird issue upon initializing qwr module in my .cpp file
NRF_BLE_QWR_DEF(qwr);
Doing so results in a syntax error
#define NRF_BLE_QWR_DEF(_name...
