Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello, I'm trying to compile the LIBUARTE example from SDK 16 but im getting undefined reference errors, this is what I've done so far:
in sdk_config.h defined , (I've...
Hi, I am really confused about the Nordic SDK and way of doing things... I have seen so much conflicting documentation.
I am using SDK_for_Thread_and_Zigbee_v4.1.0 (currently...
my project is to send pressure data from one device to four other devices, it is medical field, previously i worked in nordic openthread udp protocol using nrf52840 for mesh...
Hello
Created in SDK v17 and simple_timer example. I made a simple code to control the LED using a timer. Every 500 milliseconds, the LED turns on sequentially. LED ON and...
I recently got the nRF52-DK for using as BLE Relay evaluation.
I have downloaded following and installed to run the code
- Segger Embedded Studio (v5.1)
- nRF5_SDK_17...
https://infocenter.nordicsemi.com/topic/nwp_034/WP/nwp_034/nwp_034_intro.html?cp=16_2
download PDF link not working. Perhaps replaced with other white paper(s)?
Thank...
Hello!
I have the following component in my device tree:
I would like to retrieve the PWM device and the associated pin number (pwm1 and 0x14). I tried:
Which...
Hello,
I am trying to develop a firmware to read pulse oximetry and heart rate data from this Sparkfun module (SEN-15219): https://www.sparkfun.com/products/15219
The...
Hi,
We mainly need AWS_Jobs, FOTA, Low Power, GPS, ADC, GPIO, certificate updates and whatever is related.
Currently we working on a project that uses:
- nRF9160 ...
Hi All:
I am trying to develop a project based on Heart Rate example. SDK version is 17.0, the receiver software is based Android-nRF-Toolbox.
Now, I can transfer ADC...
We are observing unexpectedly low throughput on the Mesh GATT Proxy service. Specifically, the Nordic device (acting in the GATT server role) is only sending one PDU on every...
Hi,
I have been looking into connecting two development boards over BT.
Previously, I managed to connect an nRF52833DK to an nRF9160DK.
https://devzone.nordicsemi.com...
Hello,
I am trying to enable the read protection on the NRF51822 on a custom board. By looking through the forums, I found different ways to try and enable the read protection...
