Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I need to add secure networking. How does one add the library module ncs\zephyr\subsys\net\lib\tls_credentials to a project? I tried editing CMakeLists.txt which caused SEGGER...
The interactive GATT client of the 'ble_app_interactive' example has multiple issues. As I heavily modified the example, I'm not able to provide a diff against the original...
Hi,
I am interested in using a pair of NRF52840 USB dongles to communicate on the L2CAP layer. I have flashed the dongles with the Zephyr's hci_usb samples, and have been...
Hello,
is there any guide or documentation on Nordic Infocenter regarding configuration of BLE project for nRF5 (especially nRF52) for running FreeRTOS?
I'm aware of existing...
I have question regarding nordic soft reset. Is there any problem with nordic chip if I soft reset nordic continuously after specific interval( ex. every 5 minutes ) of time...
Hello, i am looking for documentation in regards to interfacing a external mcu with Nrf52811 via UART.
Is there a UART example or AT Client that needs to be flashed to the...
According the documentation , the msb 16 bit should identify the module, so why do I get 0000 here?
0xCA appears to be the module code for the nrf tls interface, as it's...
Hello,
I am using the NRF52-DK softdevice 6.0.0 and NRF SDK 15.0.The app is based on on the saadc PCA10040 S112. I want to add static const nrf_drv_timer_t m_timer = NRF_DRV_TIMER_INSTANCE...
Hello I am in a development stage
1. MBN52832 soc
2. s132 softdevice
3. nRF5 SDK v15.2.0
4. SPI PHY
So my concern is I want to port serialization library for SPI...
Hi, I hope it is fine to post a question like this since I'm not familiar with the license/copyright issues.
I have a friend of mine who wants to post BLE lectures using...
Hi, all.
I m trying to combine two example spi + timer using nRF52832.
But spi_event_handler function in the ex spi and timer event in the ex timer are crashed.
...
hi,
how can i scan for other BLE advertisments on nrf52811? there is no official documentation showing how to have Central role on nrf52811 softdevices! and no support in...
Can I still use the USB while the nRF9160DK is set up for current measurement as described in the spec, where power is applied on P28 after cutting solder bridge SB43 and...
