Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
My project is using QT program and nRF52DK borad.
I want to UART communication with QT and nRF52DK.
#1. If i write "hello" in qt program like below...
===========...
I saw this post for SDK v12.2:
The FDS requires data to be word-aligned
devzone.nordicsemi.com/.../how-to-force-word-alignment-for-fds
Is that still true for...
Hi,
My target is to update the application firmware running on the nRF module using serial wire connection.
I currently do experience the issue, that DFU process completes...
I am in the initial phases of porting an arduino project using the NRF52832 to the Nordic SDK (14.2 for the moment) and am running into issues when using TWIM and an event...
Hello
Im trying to figure out where the health model client sends the health messages. Ive tried doing prints in all of the send methods in health_model_client.c but not...
Hello,
I'm having an issue when I try to connect to my device from an iPhone X. I'm using SD132 v6.0.0 on SDK 15.
The phone tries to connect and then it times out. All...
Hi!
After connected and get log info "Connected." I start bonding:
but there is no any success message.
Therefore nRF52 SDK15 can't to made secure bond.
Why?
Hi,
I'm using the light_switch example to implement mesh. How do I display the RSSI value of server on rtt viewer when the client receives the server status?
Regards,...
Is it possible to modify BLE_CONN_CFG_GAP after the softdevice has been enabled? I want to be able to set the event length on start up based on a setting stored in flash with...
Hello everyone, I am looking to make a small tracker using nRF52832 chip. Can anyone please suggest me a board and a coin cell having very small dimensions so that my tracker...
I am looking for a solution to create a very low latency (<10mS) audio link for continuous streaming.
Is the proprietary mode on the nRF52 series able to do that?
Is there...
hi
In Provisioner
in function app_default_models_bind_setup()
check the following lines
/* Bind health client to App key, and configure publication key */ ERROR_CHECK...
Hello,
I am creating a project through the MultiLink example.
One problem occurred. If the device is attached to NRF52DK, the connection will be disconnected immediately...
Hi,
I am running nRF5_SDK_15.0.0_a53641a\examples\peripheral\usbd_hid_composite and find it can work in standalone mode. However, if I go to Keil or IAR debug session...
