We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hi Nordic Team,
I am planning to develop a Matter-over-Thread end device (sensor) using the nRF54L15 , which will be battery-operated . To maximize battery life (minimum...
Does anything exist yet? The datasheet only contains a preliminary matching network and says will be available when the chip enters mass production, but nothing is available...
I tried used Nordic's UART service implementation as a starting point and everything works but I can't figure out where the string "Nordic UART Service" from "nrf connect...
I have loaded the Quick Start Application using nrf connect for Desktop after following the instructions. I get the error as per the attached file on the Serial Terminal....
Hello,
We are trying to test our custom board with nRF9161 in a new location, so we bought local SIM cards (Yettel, Serbia) here. These are not special nb-iot SIMs, just...
Is there a way to modify the distance measurement sample code to where it is intended for one transmitter and multiple receivers versus between just two devices? I am trying...
The workaround says:
" Trigger TASKS_PLLSTART before TASKS_XOSTART is triggered and trigger TASKS_PLLSTOP after TASKS_XOSTOP is triggered."
I would like to start HFXO...
Hi,
I am running into a really strange issue where setting both CONFIG_NRFX_PWM0=y and CONFIG_NRFX_PWM1 =y in prj.conf gives me the following build errors while using mcuboot...
Hello,
My PPK2 is reporting 2 zetta amperes power usage, and I found out that the "modifiers" appear really broken:
I have attempted to re-flash the ppk2 firmware, but...
I am trying to format an external flash chip with littlefs, but keep getting an MPU fault. I can erase the chip, but not mount or format. I have tried writing and reading...
I'd like my VS Code build configuration for my project to be included in version control.
It seems like this configuration is stored somewhere in the "build" directory that...
Description:
I encountered an issue where my NRF54L15DK development board fails to connect to my Windows 11 PC. Upon plugging in the board, the LED near the debugger starts...
Performing a DFU with an iPhone works in some configurations and fails in other. Android consistently works.
The failing version of iOS is:
iPhone 12 mini
iPhone 13...
I'm trying to connect a SIM800L to my nrf52840-dk which I power through 5V USB. I'm a beginner at electronics so just want to make sure I understand how to wire things, please...
Hi,
I would like to know what are the prerequisites to get the ICCID of the sim card:
This is the code I use, nothing special. I can get the IMEI of the modem but not...
