Hello, I have NRF D 24LU1P 1201FD and NRF F 24LU1P 2136IW. The first one executes all commands, while the second one does not work for writing and erasing. I tried to erase...
Hi! Could you clarify a bit about Bluetooth mesh gateways' implementations. I wonder to know possible ways of Bluetooth mesh gateway implementations. How is it possible right...
Hi everyone.
I catch a terrible issue
When I use nrf52840 and NUS Android app and had for a short time a bad rssi (because of long distance between Android and SoC) and...
Hello
We need to scan for more than 8 devices, so we can't use witelist directly.
We have an idea to use presaved IRK and mac-addresses and use scanning without witelist...
Dear Nordic,
Do we have ready-to-use keyboard driver with scanning/debouncing?
I've not found an example or docs about using KSCAN with gpio-connected keyboard...
Hello. Please excuse these potentially silly questions, but I've been given the task of monitoring battery charge while also achieving maximum energy savings.
A wearable...
I just got a NRF9151 dev kit and I want to build the image as non-secure, using: nrf9151dk/nrf9151/ns. The build is failing with error: C:/ncs/v3.1.0/nrf/modules/trusted-firmware...
Hi,I made a 52840 board ,it's p0.18 hanging, without connecting a 10k pull-up resistor and a 100nf capacitor to ground. I connected 3v3, GND, SWDIO, and SWDCLK from the 52DK...
NRF54L15 NCS 3.02
I have to change my BLE advertising from Legacy to Extended. Looking at the Zephyr example "advertiser" which compiles & runs fine, but I notice that behaviour...
Hi,
I am currently trying to connect a nrf52811 as an companion to an ESP32 user UART.
I am using the interrupt driven UART implementation as kind of the last resort....
How can I set a custom interval for *extended* advertising?
I'm currently calling bt_le_ext_adv_start ( struct bt_le_ext_adv * adv , const struct bt_le_ext_adv_start_param...
~~~~~~~~~~Environment ~~~~~~~~~~ nrf54L15 + NCS 3.1.1 + VSCode + Win11 ~~~~~~~Reproduction Steps~~~~~~~~~ 1. without pm_statics.yml, with following configs (see attachment...
Dear Team,
I am experiencing a weird issue with the firmware on my custom EV board with NRF54L15.
My firmware is using MCUBoot and partition manager (I use a separate...
Dear Team,
I need to switch LXFO to internal RC for MCUBoot, however, I am experiencing troubles configuring it on NCS 3.0.1 (NRF54L15).
If I just add my RC settings to...
Hi,
Our project requires an unusual combination of running BLE, Gazell, and raw radio packets for time sync simultaneously.
Time sync and BLE are infrequent activities...
Issue:
I would like to bring to your attention that I am getting an error when running the 'list command using the nrfcredstore cli utility, while trying to retrieve the...
Hi,
I've run into an issue when doing some compatibility testing between our client's legacy device (802.15.4 transmitter) and the current device in development (802.15...
In the introduction to the bare metal SDK option for the nrf54L:
https://www.youtube.com/watch?app=desktop&v=31znTI-hnCQ
it mentions at around 58:00 that single bank...
I am using nrf connect SDK toolchain version 3.1.1 and nrf connect sdk version 3.1.1 , By default I don't have zigbee related samples/examples and also zboss stack library...
The original question was: "The nRF52840 PS mentions, that this chip contains an ETM but it does not mention the implemented version."
Researching the topic more, I found...
