Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
I’m working on a custom board based on the nRF54L15. I’m using MCUboot Serial Recovery over UART and I’m seeing a repeatable issue I can’t reconcile with the docs.
SDK/Tools...
Hi, I'm working with multiple versions of the nRF Connect SDK (v2.8.0, v3.0.0, v3.1.0) using the official VS Code integration on Windows and could verify this also on Ubuntu...
Hi, I am trying to run the Wi-Fi STA sample on nRF7002DK .
With nRF Connect SDK v2.9.2 , the STA sample connects successfully to my Wi-Fi AP (router).
With NCS...
I am using vscode on linux, I started by programming the blinky sample onto the devkit, without issue. I then moved on to the gnss sample in a separate project, this worked...
When we run test case SED&MED 3.5 , the following inconclusive result happens:
COM78 command: ot test tmforiginfilter disable COM78 FUNC __executeCommand failed: Error 35...
Hello everyone,
I need to save a core dump on my NRF54L15 internal flash in order to debug an issue. I've been following the "Debugging and Troubleshooting section" of the...
Hi everyone,
I am facing an issue when modifying the peripheral_nfc_pairing example.
Due to hardware limitations, my device cannot integrate an NFC antenna. Instead, I...
Hello. We are evaluating the nRF9151 SiP as a potential solution due to its low power consumption and compact form factor . However, our team has limited experience with firmware...
Hi,
I'm considering the implementation options for nRF91 GPS front end. Having a shared antenna for LTE and GPS would be tempting, but I'm concerned about the filtering...
Hello,
I am trying to get some basic examples working with my new NRF9151DK and running into quite a few issues. Note that this is using a onomondo sim card that came with...
Hi,
With NCS v3.1.0 and Nordic's downstream zephyr ncs-v3.1.0, I got build failure with following message:
--
warning: attempt to assign the value 'n' to the undefined...
Hello Nordic team,
After many hours I have not been able to get socket dispatching working with Zephyrs MQTT client, and I am not sure how to proceed.
First of all I would...
Hi Support Team
Due to there is very little space of C: drive of computer, so I moved the NCS SDK from C: drive to D: drive. The VS code can't recognize the SDK and toolchain...
There are 100s of solutions on the zephyr git and the nordic git. It took me a while to understand it all and it took me hours of debugging and frustration before I ended...
