Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I´m using the NRF52810 device and have an issue with the SAADC peripheral.
I basically have 2 channel where i want to do some averaging to improve noise.
The setup...
Hi,
I was exploring TWI master with TWIS Slave example in SDK16.0.0.
It works for sequential reads in loop-back mode.
Now I connected the simulated eeprom slave...
hi, I set up the environment according to the nrf_sniffer_for_bluetooth_le_3.0.0_129d2b3 file downloaded from the official website of nordic, the operating environment is...
Dear Nordic Team,
we have unstable communication with an Osram BT device through nRF52840. We got information from Osram developers the nRF52840 is the right device for...
Hello!
I have question about Direction Finding in nRF52811, Angle-of-arrival to be exact.
To begin with, I have a custom board with nrf52811 onboard and 8 antennas....
Hi
As far as I know, NFC supports peer-to-peer communication, so I want to know whether peer-to-peer communication can be achieved between two 52832 through NFC? Is there...
Hello everyone.
Iam working on a project where i need to detect a falling edge from a ADC (ADS1298) when new data is ready at a sample rate of 500SPS. I have the issue...
Hi Great Nordic Support Teams:
I'd like to know schedule of nrf9160 specification:
1.When will 9160 support R14 regulation in NB-IOT/ LTE ?
2.When will Nordic release...
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1 and Segger for flashing the image. I am using ‘ble_app_blinky’.
1) I ported UART into my code and it...
Hey all,
I would like to make a flexible design with ability to assemble NRF52832 or NRF52810 , both are pin to pin compatible ,
But i just wonder how to consider regulation...
Hello,
I am developing a capacitive sensing application with the nRF52 DK and Segger Embedded Studio. So far I have integrated the Capacitive Sensor Library Example into...
Hi everyone,
I am working on a project with the NRF9160 DK where I want to use the UART3 channel.
The issue is that I got compiling errors when I add CONFIG_UART_3_NRF_UARTE...
Hello,
I want to test the Thingy Mesh Provisioning Demo v0.7 with the codes provided on the GitHub:
https://github.com/NordicPlayground/thingy52-mesh-provisioning-demo...
Hi,
I am using s140 v7.0.1 for nRF52840.
I found if I configure NRF_GPIOTE->CONFIG[0], then BLE will not work.
Which GPIOTE channels are used in s140?
Thank you.
