We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
i am using ble_app_gatts example as beacon observer ,till 10 sec after powering up device i need connectable advertise after that period ,as i switch the advertising from...
Can you do successive updates to a Notify Characteristic using sd_ble_gatts_hvs() during the same connection interval without losing data.
The question comes down to, does...
Hi! I've successfully set op an OpenThread MQTT broker using a Rasperry Pi and nrf52 dongle and I am able to publish and subscribe to and from my computer by flashing the...
Hello!
I am working on sdk v17 and ble_app_uart. I'm going to make a button function first in this project. I created 3 functions of 'push, release, and long press' using...
I am not sure whether this is an issue with the nRF53 Engineering Example or with the SEGGER software.
I don't see any errata describing the behaviour I am experiencing...
Hello,
Is there an option to add to thread ncp example a FEM support?? I do according to de guide on the page https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsdk_tz_v4...
I am following this series of tutorial " BLE Advertising, a beginner's tutorial ", BLE Services, a beginner's tutorial .
The problem is after establish a fresh advertising...
Hello,
I got an error 8(NRF_ERROR_INVALID_STATE) while running ble_nus_c_tx_notif_enble function.
The SDK document shows that, the err_code is
"this API propagates the...
I'm evaluating using zephyr for an nRF52840 based design. I'm able to use the nrfx drivers via Kconfig options. It doesn't appear that there any other Nordic SDK libraries...
Hello developers.
I successfully ran the Mesh project with Light Switch example on nRF52840 devices. And I have 2 questions about this.
Question 1: How can I access from...
Hi.
I'd uesd RTT viewer before SES.
RTT viewer has the menu for saving logs.
I'm a new for SES. I'm recently using SES.
I can see log message on SES, but I don't know...
Hi,
I am just unable to find the FW ID for SD v7.2.0 anywhere.
I am using SDK 17 and s140 7.2.0 and am trying to create a DFU package to update both the Soft Device...
Hello All,
We are testing power consumption nRF52810 in system ON mode , my configurations as below,
Device will advertise for 10 sec connect with the mobile app sends...
