But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
We are developing a device that has different "modes", and in some modes it acts as a HID keyboard and mouse, but in other modes it does not. This device connects to iOS and...
Hi guys,
I am using the nRF52832 board and after I enabled my device to measure the temperature and return this value, now I will like to save that value in non-volatile...
Hi,
Had a project working and compiling beautifully, all ready to go, last thing to do just upgrade the SDK from 17.0.0 to 17.0.2 and the s132 7.2.0
So I change the...
Hi
I start in programming on nrf9160 DK with a sensor BME280. I followed the tutorial "getting started part 2" (https://devzone.nordicsemi.com/nordic/cellular-iot-guides...
Hello, dear sir:
In my opinion, HFXO means external oscillator, I need to buy a external oscillator because it is not exist in nRF9160?
HFINT means internal oscillator...
I use sdk16 on nrf52810 for development, but I want to use long broadcast packageada. What should I do?
A short broadcast packet can only be 31 bytes
thank you!
To the kind attention of Nordic support team,
I was reading in peer_manager library that when a ble connection is established, using the connection handler as a parameter...
Hi ,
In our actual design, we are using nrf52810. We have done all our development on nrf52832, as there is no Eval Kit present for nrf52810. We are porting our development...
Hello,
I can see RTC drift of around 14 seconds in 1 hr when I select the internal RC oscillator in sdk-config of nrf-calender example.
Is this much drift expected? In...
I would like to add events for button release and button long push to my application. I also want to keep the SDK folder unmodified for easy upgrades.
To do this I copied...
Hi,
In my project, I am using High voltage mode [VDDH] in this case automatically REG1 [LDO] will be enabled. But my question is as per the datasheet i understood that even...
Hi.
I am developing using nRF52820 example source using SDK 17.0.2.
USB and LESC were added using S112.
However, during operation, the following HardFault error occurs...
Hi everyone,
I am trying to integrate the DFU service into my application on order to achieve buttonless OTA DFU but I am not able to implement it so far and I need your...
Hello,
I merged the two projects usbd_cdc_acm_pca10056 (A) and ble_app_hids_mouse_pca10056_s140 (B) by copying all additional contents from A's flash_placement.xml into...
Hello,
I am trying to send data obtained from a SAADC port via BLE using the ble_nus_data_send function. This must happen periodically at frequencies within the Gigahertz...
