Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am porting RF evaluation code to the nRF53 NCS/zephyr/Segger Embedded Studio toolchain, using only the network core to start.
How do you recommend configuring the network...
Hi,
I am trying to install Command Line Tools on Ubuntu 16.04. But I am not able to find the download link for it. The page shows ERROR 404. Can someone direct me to the...
Hello,
I am need to add voltage sampling functionality to existing FreeRTOS framework on a low-power BLE device. When I enable BLE, I get 3mA of current, which stays there...
Hi,
When I call sd_ble_gap_disconnect( m_conn_handle, BLE_HCI_REMOTE_USER_TERMINATED_CONNECTION), it usually takes about 100 msec, and come back with event BLE_GAP_EVT_DISCONNECTED...
When not using the SWD port I would like to pull up the SWDIO and SWDCLK lines high. Does the NRF52810 have internal pull up on these two pins? If not, what value pull-ups...
Hi,
I have received nRF52840 development kit recently and I am trying to work with Proximity demo application on my mobile phone. The problem is no device is shown on the...
My Project involves adding BLUETOOTH mesh to a current product.
In that product we use the Flash Data storage library to read and write flash. The SDK for mesh documentation...
Hi ,
I tried to download nRF Command Line Tools for linux 64 bit from your server today (01.22.2020). Even though I chose linux 64bit operating system, clicking on link...
Hi,
I bought an nrf51822 beacon from ebay, it has an LED and a button. I am trying to figure out what pins the LED and the button are connected to, without much success...
Hi,
I have cloned code from https://github.com/NordicPlayground/thingy52-mesh-provisioning-demo and everything was looking great.
I have built and loaded code to my 2...
Hello,
on nrf52832, sdk16 S132, I'm using timer 4 and Compare system to step forward in a PWM sequence. everything is going very well until I have more than 3 PPI Chanels...
Hello,
I am using BLE peripheral. I want to send more than 200 bytes of data to the mobile phone. What I need to do in the characteristic definition and after that.
...
Hi .. i am new to pwm, i want to drive the gear motor for that i need pwm pin , which pin i can configure , how to do ? how to configure the pwm pin . which example will be...
Suppose node L is in a friendship with node F. Consider the following:
1. Some other node C sends a message to L.
2. F hears the message, and saves the message into...
