We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello!
I'm currently testing writing and erasing data to an external Flash using an nRF5340 and a NOR Flash, the mx25r64.
I'm going to use the SPI_FLASH example.
I bulid...
Hi,
I need to read 16-bit values from a sensor using SPI on the NRF52840. However, since the SPI peripheral only supports an 8-bit word length, what is the best way to handle...
We have nRF5340 LE Audio dks. We intend to check the PDUs transmitted. Does wireshark nrf sniffer support this if yes then how and if not then what is the possible way to...
Hello I want to operate one RGB LED SK6805-EC10-100 for that i need to write data bit by bit in between need to use some delay if any API is there please let me know.
...
Hi,
I noticed that the f_sector_cnt element of the fcb struct is a uint8_t .
How is that supposed to handle large flash sizes? I mean even with a sector of 64KB, the FCB...
Hello Nordic Semiconductor Community,
I am currently working on a project using a custom board based on the E73-2G4M08S1C SoM, which features the nrf52840 chip. For flashing...
Hi
What is the timestamp accuracy of the nRF51 DK based Sniffer, nRF52 DK based sniffer,
I want to measure the actual accuracy of my advertisement interval, preferably...
I’m working on a device using a Nordic chip and the following setup:
nRF Connect SDK : v2.5.2
Toolchains : v2.7.0
We need to minimize current consumption during...
Hi,
I updated my NCS to V2.9.0, I try to build my project, but it fail(it's OK at V2.8.0). the output message (attached file); Please help to check the message , how can...
Hello!
I have been testing the distance measurement functionality on the nRF52832, and it performs up to approximately 10–12 meters in an office environment. Switching to...
Hello,
I am working on connecting a NRF9161 to a MQTT server (EMQX) but i am getting a connection error (-12), I was hoping someone could help me navigate this one. It...
Hello Nordic team,
I am working on a project where I want to use an nRF52850-based board as a DFU controller to transfer a DFU package to a DFU target device (another Nordic...
I'm trying to install NCS v2.9.0 from within the VS code nRF plugin, and it always fails every time I try. Below is the complete install log.
I've seen various other posts...
