Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
I am trying to interface a PDM microphone to a NRF52840 using NRF Connect SDK v2.9.0. Does anyone have a good idea of how to get the DMIC sample to work on the NRF52840? The...
I am trying to use an ESP8266 ( ESP-01) to add Wifi capabilities to a nRF9160 project board. I am using nRF Connect SDK V2.9.0 and the V2.9.0 Toolchain.
To set it up I followed...
I have an NRF52840 DK (3.0.2) board, but it is not working. The USB port is not detected. When I power it through USB, the debug LED (LED5) turns on and then off. On the SoC...
Hi，
SDK:ncs2.6.1. The main program runs in the app core, and the net core is included as a child image. The Bluetooth broadcast is normal when tested at room temperature...
Hello Team,
I am trying to measure the sleep current of NRF54L15 DK, in the system ON mode, for that I am using Blinky sample code, from SDK version 2.9, which uses the...
Hello,
i recently received several nRF54L15DK kits.
The example good for channel sounding works well but left us with a question about the BLE antenna.
According to...
Hello when I build an application on VS Code, the terminal give this error :
warning: UPDATEABLE_IMAGE_NUMBER (defined at C:/ncs/v2.8.0/nrf\samples\common\mcumgr_bt_ota_dfu...
Do we have documentation anywhere detailing which pin is used or not in the 9161 DK and 7002 DK? I see docs like this:
Board control
Buttons and LEDs
I selected pin...
Hello ,
i m using sdk 15.0.0 and spi example for flash winbond 25q64 read write .
i m successfully read manufacture id,,device id.
but problem is writing and reading...
I'd like to know if the below info. is correct.
QDID of the nRF5340 chip itself : 11524
QDID of the Host system used in nRF Connect SDK version 2.8.0: Q322804
BR...
Hello,
I am using the following device and development kit:
Device: NORA-B106-00B (nRF5340)
nRF Connect SDK: 2.0.2
Currently, to ensure that the connected...
I am currently working on a custom board with the nRF9160. The modem initialization function nrf_modem_lib_init() terminates with an error.
The error log is as follows:...
While working on a device for personal use, I needed to reference some official BLE documentation. I noticed that many of the documents — including:
[BLE Core Specification...
I upgraded from v2.7.0 to v2.8.0 of the nRF Connect SDK and noticed that the UART was no longer working.
It seemed the UART receives one byte and calls exit. Transmit doesn...
Hi,
Apologies for a newbie question (I am far from a developer and just need to flash firmware)
I have a nRF52 DK connected to my PC running nRF Connect for desktop...
