We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
I would like to know which pins are available for nRF5340 on Thingy91 X on the debug board interface.
I was looking into PCA64165_Schematic_And_PCB.pdf and PCA20065_Schematic_And_PCB...
I would like to achieve TX-POWER control using GPIO mode GAIN control on the application core in SDK_VerV2.8.0, similar to how it was done in V2.3.0. Could you please tell...
Hello,
IDE - Visual Studio Code
SDK version - 2.9.0
Computer platform - Win11
I'm at the early stages of a project which first requires to send ~10K of data to the...
I'm encountering a build error when compiling a project with both Wi-Fi and the PSA Driver for CryptoCell enabled in nRF Connect SDK v2.9.0. The error occurs in crypto_mbedtls_alt...
Hello,
When using extended advertising with coded PHY, the advertiser address is included by default in the auxiliary packet (AUX_ADV_IND) on the data channels and not in...
I ma supposed to read FA0A03048100020000F , BUT I END UP READING FA0A030482000202020202. This is also common with the peripheral i am trying to interact, It sends a packet...
Hi everyone,
I´m work on a project were i have to stablish a mqtt connection with a RabbitMQ broker thats have user/pass auth and tls without certificate validate. My...
Hello, The Online Profiler tool currently doesn't support the nRF 9151. Is there a possibility it will be supported in the future? In the meantime, if I choose the nRF 9160...
Hi,
I've been working on Nordic boards for almost a year now using Zephyr and nRFConnect. I've been able to understand the DevAcademy Courses and to reproduce them.
The...
Hi,
I am working with the nRF52 DK running the Blinky example , captured BLE packets using the nRF51 DK sniffer and analyzed the interval timings across the advertising...
Hello,
I've got the nrf9160dk board, but the nrf91 isn't visible. I was told that it's dead, and I should try to play around, at least with the 52840. I've tried to make...
Hello, I am currently working with VEML6035 light sensor and so far i had a hard time working with its 16-bit registers.
The code that i wrote:
overlay file:
I can...
Hi,
It seems like my system is crushing before going to deep sleep,
I have noticed that if I remove a k_sleep of 500 ms, just before going to deep sleep the system does...
It's successful when I use west :
% west flash -d build
But it's failed when I use nrfjprog :
% nrfjprog --program merged.hex --reset
OR
% nrfjprog -f unknown...
