Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
Is there a script with which I can flash a nrf52 directly over Bluetooth. I tried to use "nrfutil.exe dfu ble -ic NRF52 -a mac_address" but it requires a board to be connected...
Hi,
In oner of new project, we planned to use nRF 52833 with BLE mesh implementation.
We are planned to use IAR 8.50.1. We have downloaded both nRF SDK(17.0.2) and mesh...
I try to use 52832 as a frequency meter to measure the bluetooth central frequency to do crystal trimming.
The target is a CW(continous wave) signal, like 2441MHz,which...
Hello, I meet some problem. The chip I used is nRF52810 QCAA, the softdevice I used is s112, I defined P0.09 as SCL and P0.06 as SDA, the TWI can't work and it stops in while...
Short Our project runs application code on the nrf5340 application core and a bt_mesh configuration on the network core. Everything works as expected when we build as two...
Hi, I am Marcous.
Recently I am doing the AoA project in the nrf52833 board. I have now got a antenna matrix, sky13322-375LF , a board with four antennas in it and 4 gpios...
Hello i've implemented a push button detection with the bsp library but i can't fin a way to configure a pullup with it :
When i check the tention on the input it's at...
Hi Nordic DevTeam,
What I have learned from this thread below is that using 32kHz external crystal provides less power consumption and better accuracy :
https://devzone...
To the kind Nordic support team,
We are evaluating a scenario where we need a "gzll gzp host" to receive data on two encrypted pipes at almost the same time (we modified...
i was running some power optimization and MTU tests in NCS V1.5.1 and was able to compile and run.
I upgraded to NCS V1.6.0 and there were several errors
So when I compile...
Hello,
I am currently working with the development board nRF5340DK in order to evaluate the nRF5340 SoC.
Given certain project requirements related to the operating temperature...
Hello,
I am new on Nordic controller platform and i want to make the GPIO pull down and pull up at run time and also change the IO direction.
How i can do that please...
I am using the FAT FS on the nRF9160-DK to store data on an SD card.
The CLIB library provides Linix-like fopen, fclose, …
The flags passed to fopen are strings like ...
