At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Good day!
I'm interesting in ability to support of some required Cybersecurity features by NRF52832 or/and NRF52840:
Is it possible to fully disable JTAG and/or SWD...
I am getting the following error message in the log when I try to connect with an Android device. It remains connected for about 40 seconds and then automatically disconnects...
Hi. Nordic.
Now I'm developing custom DFU transport which was already developed with SDK 12.x.
At the time of SDK 12, fs_evt_handler calls user's callback with the result...
Hi. I have added advertising to my multilink central project SDK15.0. Running on a nRF52840.
I get a error 12 when advertising_start(); is called on startup. I believe this...
Hey all
I've some basic question about the Call-Stack.
In my application I have a series of functions which call other functions and so on until an depht of about 20 calls...
Hello. How i can do a simple read an 0 -> 3 Volt (vdd) signal on Analog 0 P0.03?
I try it with saadc without sucess
int result = 0;
NRF_SAADC->CH[0].CONFIG = (
...
Hi everyone, I know that this topic has been mentioned before, but there are a lot of doubts and the situation about measuring a battery is still not clear.
1) First of...
Hi,
Here i are using nRF52832 ,softdevice S132 and mesh sdk v3.0.0
I am facing an issue in UART configuration in mesh (LIGHT SWITCH EXAMPLE) server code . When using my...
Hi all,
I am building Border Rounter and Thread Network. I using SDK 3.1 and image newest for border rounter
I follow this link https://infocenter.nordicsemi.com/topic...
Hello. I am working on a application in a NRF5238 with s132, where I send 20 byte packets using notifications from a peripheral to a central board. The central is a modified...
I updated to SDK v1.0.0 today and have not been able to build sample or application solutions since. I updated the SDK, modem FW, and SES.
For example, when I open and try...
Hi,
I'm sorry to borther you in your holiday.I got a issuse about 52810 (s112) with PA.I found my device would reset when I call ble_advertising_start() after calling pa_lna_init...
I'm trying to implement Serial Wire Debug to read some Data from Nordic from other Controller. Initially Need to read some registers in DP & AP Nordic. For that I need to...
Hi guys, i was using nrf51822 s130 sdk, and now i am using nrf52dk s132 sdk. When i am using nrf_adc.h, all bitfields macro's get errors. It's bitfield macros doesn't match...
