At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hi everyone,
Im looking to put together a security solution consisting of an accelerometer and a proximity beacon. The accelerometer would be installed on gates and authorized...
As part of our evaluation on the Nordic BLE SOC, I want to measure the throughput, range and the power consumption.
Can someone point me to any sample program(s) that I...
A while ago I was experimenting with the usbd_msc demo, trying to get the firmware working as RAM-disk-only storage, without any permanent storage like Flash or SDC. While...
Dear Team,
We need a SoC which can support the following features for our wearable product.
1) Battery Charging
2) I2C interface for sensor
3) GPS
4) BLE
Regards...
Hi, I have run light switch example in SDK 15.2 and SDK for Mesh version 3.1.0, when I try to add new app_onoff_server_t model to Server with my code:
and I have modified...
Hello,
i noticed that even i send AT%XMODEMTRACE=0 with response "OK" the bsd lib triggers EGU0 / Trace interrupts. The modem is not started, but the bsd lib got succesfully...
We are using a Raytac MDBT42Q (nRF52832) Bluetooth in one of our products.
We are using nRF Toolbox for Android/IOS for testing. Is there any Windows 10 nRF Toolbox??
...
hi guys, I'm confused about bluetooth 5. Is there some example that use it? i have a nrf52840 board and i will like to use it in order to send my data but i didn't find any...
HI
I am trying to develop a mesh network using nordic mesh SDK..where nrf52 dongles will be beacons for which beaconing example will be used and from SDK
52840 DK will...
I startet evaluation with nRF52840 and SES.
I found the BSP Demo to crash (HardFault in Debug) after app_timer_init() , because of a NRF_LOG_INFO() inside, but Logging not...
Hi Sir,
As the title, can 51824 support BT 4.2 in Zephyr? Any document (or link) descript this?
If yes, which SDK version we can use?
Thank you.
BRs, Han
Hello,
I am working on nRF9160dk. I want to send gps coordinates via sms using nRF9160dk. Last week, I tried simple_at program to send sms and it worked. Now I am working...
When I am receiving data from slave data is missing. Means if o am reading 255 bytes then 127 bytes are right after that I am receiving alternate bytes. Some times I am receiving...
Hi,
I was wondering if anyone has sample code that would support a 16 x 2 LCD over an I1C interface.
Something like this.
https://www.amazon.co.uk/HALJIA-Character-Backlight...
