We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello, we are using the nRF52832 for building our custom board.After loading the example bluetooth_uart code given in the SDK, our board is not producing correct RF(Bluetooth...
Hi, I have a BMD-300 (nRF52) module that I'm attempting to program with OpenOCD and an ST-link from Linux (it worked great for nRF51 so I was trying to keep the same tools...
Hello,
I have been trying to have a central/peripheral device read UUIDs and RSSI values from surrounding peripherals using their advertisements and without actually connecting...
I'm attempting to add the bonding components from the ble_app_hids_keyboard example to the ble_app_uart example. I've gotten everything configured to the point where I can...
I am connected with this correct com port but Device discovery is failing to start.
First it says NO response from master emulator then it fails to start. Please help me...
Hi, I see that in the nrf52810 reference layout ( Nrf52810 Reference Layout ), all the capacitors and inductor have 0402 or 0603 footprint. i would like to switch the foot...
i followed this custom service tutorial.
but when i changed the RAM_START and RAM_SIZE address it getting below error, im using S132v5 softdevice
<warning> nrf_sdh_ble...
Are the PCB antennas provided in eagle library of NRF52810 ( github ) require any additional components for impedance matching or i can directly add the PCB antenna to ANT...
I downloaded radio_test.c from Nordic and complied it to output a .hex file. Now I want to flash this .hex file onto nRF52832. Does it require to softdevice and bootloader...
Hello (I'm new to this nRF-world...).
I am searching for a small "nRF-52832 clock" (arm mounted watch) that at least reports the "surrounding/room temperature" (not only...
Hello
SDK12.3, nRF51822
Example Gazelle from SDK works fine. If I use the softdevice (add ble_stack_init) then the program freezes in the nrf_gzll_enable
I want to do changes for firmware upgrade nrf52832 with SDK BLE_2.0.1 for the mesh.
I need DFU (Bootloader)UART for our application to upgrade nrf52832 firmware by the host...
Hi
I have written this code based on a sample from SDK12. The board is a pca10040 and nRF52832 chip. It seems like after disconnection from the master device the Softdevice...
Dear support team,
Channel survey (RSSI report for each data channels) are now available on S132v6. However, for users who need to use v4.0.2, is there alternative method...
I am using the Hackable Kit from Electronut labs and using their Bumpy , black magic probe alternative for programming. I would like to control a servo motor precisely at...
