Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
I would like to ask for any information regarding the near-future plan for the nRF SDK for Mesh.
Are these features planned? And if so, when would they be implemented?...
nRF52832
There are three ways of working with the clock registers, a hardware access layer macro set, the nrf_drv_clock.c/h, and direct register access.
What is the...
I am implementing Device Firmware Update using BGLib on C# using BLED112. When i am writing on the DFU Data point on Peripheral (which is a Nordic's nrf51 chipset), i need...
hi,everyone.
version:sdk10.0
i know the nrf51822 system running order is: softdevice->bootloader->app.But i have a question when i am reading bootloader. If the program...
I have a question about the wait_for_flash_ready routine in the nrf_nvmc.c file.
static inline void wait_for_flash_ready(void)
{
while (NRF_NVMC->READY == NVMC_READY_READY_Busy...
Hey,
I have my nrf 52 dk and nrf connect 1.1.1.
I have soft device v3 on my nrf 52.
I connect my board into my computer, NRF connect recognizes my board and gives me...
Hello,
4 of 5 times when i want to connect to my firmware using RTT the firmware crashes.
Commands that i use are:
terminal one: JLinkExe -if SWD -device nrf52 -speed...
Hello ,
I'm using nRF52810 with SDK 14.1 base on ble_app_uart example. where i am continously receiving the GPS data via UART. i am putting my GPS module in sleep mode...
Hello,
My setup is: ble_uart_app example, custom board with nrf51822, sdk 6, s110, nrf connect for pc.
I am advertising with my peripheral device. Whitelist is being...
Hello,
I am trying to merge the code of ble_app_buttonless_dfu with the code of ble_app_uart,
because I starts all implementation with the code of ble_app_uart at first...
Hello,
I am using SDK9.0 and testing the LED_Blinky project with IAR tool, Evaluation kit. The application is executing and leds are blinking but I am not able to set a...
Hi, and thanks ahead for the help. I am working on receiving ble packets without using the soft device. I am able to transmit an advertisement with raw radio and pick it up...
Hi,
I am trying to write and update a record in flash but not receiving event callbacks FDS_EVT_WRITE and FDS_EVT_UPDATE. I found that i need to add the following code...
