But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
I received my nRF52840-DK (PCA10056) last week and today I was given the task to get started.
I started setup my environment with my preferred choice: Arduino IDE. Unfortunately...
Hi
In the actual test, the power consumption of the chip when scanning is started is 9.5mA,This actual test value is higher than the Iradio_rx0 and Is1 in the PS .What is...
Hi
The customer wants to test the RF transmit power of the nrf9160，whether the AT command can be fixed frequency?Or whether there are special tools to test RF power?
Hi,
I'm trying to migrate bluetooth softdevice to a project contained cli module. I found cli module and softdevice would all create an app timer. The softdevice first created...
Hi,
i using 52840DK 10056, keil5
SDKs\nRF5_SDK_17.0.2_d674dde\examples\ble_central_and_peripheral\experimental\ble_app_multirole_lesc\
i got err or as follows ,but the...
hi support team,
There is one problem with customer product, for modem it takes more than 5 minutes time to attach the network, i compared with DK, attach is the modem trace;...
i noticed that in the "ble_gap.h", #define BLE_GAP_ADV_SET_DATA_SIZE_EXTENDED_MAX_SUPPORTED (255). But now the situation is, i want to broadcast data more than 255 bytes,...
Peripheral: nRF52840 DK Central: OnePlus 6T, nRF Connect app
I modified ble_app_uart example, to support Bluetooth Long Range:
I observe two issues:
Advertising...
We were thinking to use nrf52840 dongle for one of our key projects. We were able to integrate the dongle in our ecosystem with android app.
But we have users of the product...
I have a problem about BPROT function, the project is on nrf52832 and using SDK 15.3, Softdevice s132 6.1.1.
If I enable the BPROT function by calling nrf_bootloader_flash_protect...
Nrf52832, SDK 13.0 Softdevice 132 PMIC: bq25150
I have a battery powered BLE device. When a user takes off the battery and put it back and powering on, the device does...
i set the connected time is 30ms
but i use dongle to grab the bag ,i find that the connection parameters were wrong , it can not fix at a value
it looks like it change...
Hello,
This issue is related to this ticket , before continuing I recommend to read it first.
I had suspicion that the "speed" improvement is between project compiled...
Hello,
I recently opened a ticket, with several questions about the mesh network, I had some evolutions and new questions emerged.
We have a firmware already consolidated...
Hell there Can I find an SDK that is supported on Nrf52805 chip? Or can I get any proper guidance on program of nrf52805 (the module MS46SFIi) together with Segger Studio...
