We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi,
I m using nRF52840 dongle to setup the nRF5_SDK_17.0.2 .
Besides, the related software and the Segger Embedded Studio are installed.
Occurred Problems :
When...
Dear members,
How can I wake up the system after idle ?
It goes to main loop, but never wakes up if there's a signal from HRM,BSC or B.Power after search time out and...
Dear everyone.
Sorry for my cheep question.
We are using nRF51822 as Bluetooth4.1 with Softdevice S120 and S110 .
Is this device affected by the "BrakTooth" attack?...
Hello,
I am currently working on a project that requires to sample a 50Hz sine wave and transmit the data point over BLE, which will need around 10 - 20 samples per cycle...
Hi There
I’m hoping to implement a low power always-on/listening (response time <10s) industrial product in the UK
I’ve spoken to several acquaintances and had conflicting...
Hi All:
We are using nRF52840 SDK with BLE Mesh sdk5.0 to develop bluetooth mesh and we can use light_sw_client to control the LED1 state on the light_sw_sever via BLE Mesh...
I am using PC code derived from pc-ble-driver heart rate collector with a nRF52840 dev board
On adding characteristics sd_ble_uuid_vs_add() I get an error of 4 - NRF_ERROR_NO_MEM...
I have an nrf52832 acting as a central device that is trying to connect to a peripheral. However, after the peripheral disconnects and the central tries to reconnect I get...
Hi,
I was looking at this page https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/gs_modifying.html and saw the following line:
"When building your application...
I am getting an NRF_ERROR_CRYPTO_RNG_INIT_FAILED from nrf_crypto_rng_backend_init during the sm_init sequence. Any suggestions on what might be causing this?
Hi Sir/Madam,
Our project needs to use TEE on nRF5340 which seems to be implemented by TF-M for now and future. After investigating the implementation, I didn't find a...
Greetings,
What is the minimum low pulse required to externally reset the nRF5340?
I see this answer for nRF51 and this answer for nRF52 . Can I assume nRF53 will be the...
Hi,
I have a nRF9160 DK and Iam trying to join my Private NB-IoT network that my company has (So I can get a static IP). I have the NB-IoT activated Nano SIM and the credentials...
