But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hi,
we're developing a firmware for the nRF52811 that makes exhaustive use of RSSI sampling during packet reception. While this gives reliable results for Nordic proprietary...
Hello,
I'm currently using fatfs with a QSPI flash device on an nRF52840 with SDK 16. I was wondering what is the best way to put the qspi device to sleep in between reads...
Hi, i have a project with NRF52832 and i try to designing 2.4GHz antenna on PCB. I use your antennas as an example while designing, but whenever I try to simulate these antennas...
The company I work for wants to make a wearable personal (care)alarm device for use outside, think of an elderly person who is still mobile but is prone to falling. This device...
hi
All video I can found from youtube and nordic website :
(such as https://www.nordicsemi.com/Software-and-tools/Development-Tools/nRF-Mesh/GetStarted#infotabs )
are...
HI,
I'm facing a weird issue where the nRF52832 breakouit would reset and upon reading the RESETREAS reg, the value is 0xC or 0X8 ,I am using s132_nrf52_4.0.2_softdevice...
Hello,
I am using nRF52833, nRF Connect SDK v1.4.2.
I have imported the Zigbee light switch, light bulb, network_coordinator build and test it successfully.
I have also...
Dear Sir/Madam,
I have bought NRF52840 dongle to bring up my prototype as fast as possible. I am new to Bluetooth tech.
My application requires following peripheral...
Can we do CTL with dimming and generic on/off in nrf mesh app simultaneously. by using GPIO pins p0.15 and p0.16. for external leds. Is external led will get off. What will...
Hello there,
I am using nRD52840 PDK and nRF5_SDK_for_Thread_and_Zigbee_v1.0.0 SDK for BLE and Thread development. I am using examples from SDK. I have merged thread coap...
Hi, I am working on implementing the security aspect of our BLE application using nRF52832 MCU with SDK 17. The goal is to establish a secure connection between peripheral...
Hi，Dear all:
I got trouble when I change “libuarte example”(nrf52840 DK, SDK17.0.2)，the default example use RTC instance :
NRF_LIBUARTE_ASYNC_DEFINE(libuarte, 0, 0, 0...
Hello Nordic Team, Over the course of development I have had to reverse engineer and pick apart various sources (DevZone, Google, Zephyr documentation, etc) in order to figure...
