But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hi there,
My question is similar to https://devzone.nordicsemi.com/f/nordic-q-a/39447/central-role-in-a-mesh-proxy-node , but perhaps slightly different in that my existing...
DFU Trigger Library (USB) is indicated that only for nRF52840 SoC. For other SoCs, can I use it after some modification of the library easily? What's the limits?
Hi !
I am on a firmware project for a nrf52832. I am using SES on Windows.
There seem to be a problem when combining buttonless DFU and NUS. When I do the services_init...
Dear devzone community,
I am currently in the process of migrating my MBED code to NRF5 SDK. My MBED code is functional and it works fine, you can find the code below: ...
There is no any Softdevice S122 listed on the page below.
https://www.nordicsemi.com/Software-and-tools/Software/nRF5-SDK
We have downloaded the SDK from the same page...
Hey guys,
right now I am using 2 NRF24L01+ modules connected to two Atmel Atmega 644P in order to collect some sensor data and send it to a computer. Im coding via Arduino...
Hello, I am able to use the Zigbee CLI Agent and send some commands. I am using the zb-cli-wrapper python package to send commands from python. I wrote an application that...
Hi,
we developed a 2D-3D mouse .It contains a 2D sensor and a 3D sensor and 4 touchpads for left click,right click and 3D motion enabling.
The SDK we are using for developing...
Hi Nordic,
I am implement watchdog function in my nRF52840 project base on SDK15.3 ,but I found something I cannot understatnd, please help.
Watchdog reload value is 10000...
Hi,
I am trying to bring up open AMP application on nrf5340.
As previously known, this is used for exchanging specific data between the app core and the network core...
Hi All,
I am Working on nRF52840 and using nRF52840-DK.
Below is my working environment
SDK - nRF5_SDK_16.0.0_98a08e2
IDE - Segger Embedded studio (windows 10 -...
hello Nordic
i am working with nrf52832, sdk 16.0 , s132 (v7)
i am trying to send and receive data from an nfc reader/writer module (NXP pn7150)
if i use nrf_delay_ms...
Hi all, I am merging TWI code with BLE. I started with the ble_app_uart example working perfectly, however, after adding TWI libs and drivers (nrf_twi; nrf_twim; twi_master...
Hi All,
we were tasked by a customer to develop software for the nRF52840 and they recommended to use segger embedded studio. We downloaded it from the Nordic web site,...
So the goal of what I'm doing is I have a Wurth Proteus III and I want to run the NRF Mesh SDK provisioner on the Proteus III. I have been told that this is possible and through...
