Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
I have the Thingy91 module, everything is working when I (turn off modem then) set AT%XSYSTEMMODE=1,0,0,0 (and turn on modem again), but if I power cycle the device the original...
Even though we passed AT%NBRGRSRP, it returns only ok like below, never returns any values:
AT%NBRGRSRP OK
Could you please advise us how to get the defined values with...
Hi Team
We are using the nrf52840 module for our application, in that we need the enable the "Micro_Ecc" functionality,
What are the steps we need to follow to enable...
Hello,
I have implemented DFU using I2C by modifying the original nrf_dfu_serial_uart.c file. Also, on the master side I have added an I2C adapter class.
The communication...
Hi,
I am a newbie and just started working on the nrf52840 board. I started by using the example "ble_app_uart" and implemented the I2C module to read IMU sensor data and...
Dear all,
I am interested in a BT mesh modules that support precise time synchronization between the modules (microseconds). This is required for sensors application that...
Hi,
I installed nrf Connect SDK 1.2.0 using the nRF Connect 3.3.2 App - Toolchain Manager. (Windows 10)
Using SES for Nordic v4.52, I opened the asset tracker project...
Is there any way I can scan for a short period of time with a duplicate filter on so that I only get 1 packet form the advertising device in one scan window.
For example...
I recently purchased and downloaded the nRF9160DK. The DK User Guide v0.7 does not match the Altium design files schematics and neither match the application schematic in...
I have project with nrf52832.
every second, i want send 11k byte data from nrf52832 to android app, but it is loss data. (i used phone ble 4.2 loss about 1-2% packet)
...
Hi,
Been starting to program the thingy91 and faced some issues. This is the second attempt after failing on the PC and now using the MAC.
Managed to follow the steps...
Hi Sir,
I use the example ble_app_uart_c, the program runs to APP_UART_FIFO_INIT() in uart_init(), an error will occur, and the program jumps to NRF_BREAKPOINT_COND -->...
The nRF52840 product specification version 1.1 contains for the table 160, 162, 164, 166, 168 and 170 the very same content. I suspect, that the correct content can be taken...
