Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
Hi everyone,
I'm developing a Matter device on the nRF54L15 platform using NCS 2.9.0. When commissioning the device via HomePod and iPhone, the device unexpectedly reboots...
Hello, Super quick but important question, are the SMD footprints in the nRF52840 reference circuitry recommended BOM (ie image attached) in imperial or metric units? and...
After full update modem firmware and reboot, i got this error:
E: Modem library init error: -116, lte_lc not initialized
The only way to work around is power cycle.Po...
Issue:
I would like to bring to your attention that I am getting an error when running the 'list command using the nrfcredstore cli utility, while trying to retrieve the...
Title
nRF5340 DK × 2 + MCP2515/TJA1050 – can_start() = -5 (CANCTRL/CANSTAT = 0xFF). What am I missing?
Hi everyone,
I’m trying to bring-up a very small CAN bus test...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
Hello!
I have tried in various ways to make the XIP part functional on SDK version 3.0 (SDK v3.0.0-3bfc46578e42) but without success, this on the NRF5340 devkit. I mention...
Hello nordic team!
Context:
Currently I am working on modifying our application code to be able to select, at runtime, which network interface it will use (between ethernet...
Hi,
am working on nrf52840 withst7789v custom display . I have integrated the my display code using lvgl library with PMIC code in zephyr . while doing that I have configure...
Hi. I had a working MCUboot configuration that I used in order to update both the app core and the net core as follows:
- Upload the app core image using mcumgr - Upload...
Hi. I used nRF Connect SDK v2.9.1 to add OTA to the Peripheral UART sample application. The target is nRF54L10, but when I build it, the flash usage exceeds 50%.
If the...
Does nRF9160 support IoT devices, SGP.31 eSIM IoT Architecture and Requirements for remote provisioning of eUICCs in Network Constrained and/or User Interface (UI) Constrained...
Hello, we've a nRF9161 DK board a we saw on the back side a footprint for mounting an SD card holder and we found the SD card holder component in the BOM.
Unfortunately...
Hlo
I have designed a custom board based on nRF5340. Now I am trying to do flashing and RF testing of it through nRF5340 development board but can't even flash it because...
I have the following pm_static.yml configuration:
and I'm trying to acces this `custom_bootloader_header` from my application code. Here's the relevant snippet:
...
