But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hey im new to the nordics family. Recently bought nRF52840dongle to work with a project im developing. So im using RFID-RC522 reader connected to the nRF52840 dongle via SPI...
Description
I’m developing a product designed to recognize people standing in front of gates.
Let’s consider the following scenario:
There are three gates , each...
I am setting up our production facility in India. Brought out our test jig software that flashes the nRF53 modules.
I use nrfutil to program the boards via "nrfutil device...
Hi,
I am using "nrfutil" v8.1.1 and "device" 2.15.2
If I have my Otii ARC plugged into USB, then "nrfutil device list" crashes nrfutil with it complaining about "serialport...
After moving from nrf9160 to nrf9151 on our prototype, our old firmware resets while trying to set up the LTE connection (this still happens when `CONFIG_RESET_ON_FATAL_ERROR...
Hi,
I am following the below link to enable the FOTA over BLE in our custom project. I have tried the "Peripheral lbs" example and it is working.
https://academy.nordicsemi...
I have programmed an nRF5340 DK with the Auracast Broadcast Audio Source application. I have a pair of Samsung Galaxy Buds3 Pro paired with a Samsung Galaxy Tab S11 running...
Hello,
I am creating my own board with a nRF5340. I see a development board with a PCB antenna. I do not have the thousands of dollars for the simulation software. What...
C:\nRF5_SDK_17.1.0_ddde560\nRF5_SDK_17.1.0_ddde560\examples\peripheral\spis\pca10056\blank\ses project is giving me the errors listed bellow when trying to run the example...
Dear Team,
I have nRF54L15-DK and my firmware is running fine over there.
Now I want to use nRF54L15-DK to program & debug standalone NRF54L15 on a my custom board....
Our existing product (already in the market) at Element Science in San Francisco, CA, USA uses an nRF52832 (BMD-350 module by u-blox) and nRF5 SDK 15.3 as base for the firmware...
Hello, I have two nrf52840-dongles which I am using to test ESB. (NCS 3.1.1)
With a few modifications to the ESB prx and ptx samples:
Remove logs except for PTX ESB_EVENT_RX_RECEIVED...
I upgraded my sdk from 2.6.1 to 3.1.1 and after resolving a few issues everything was working just as it was before the upgrade except for MCUmgr. When I run the MCUmgr client...
Hi,
I recently migrated a project from NCS v2.x to NCS v3.x and noticed that the method I previously used to generate a device-unique identifier no longer works the same...
