We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi, community.
From the official document, I have learned how network core Bootloader works.
It can write data from shared SRAM to the corresponding flash address of Nework...
Hello,
i'm programing a nrf52832 and a nrf52805 and I'm using the peripheral uart example, I would like to change the size of the bytes of my rx and tx that I can send...
Hi
I have a board nRF52840 configured with some QSPI with filesystem configured
I would like to manage the file system from an app and I saw that - nRF Connect Device...
I'm working on a project where we need to store into FLASH about 1350 bytes of compressed data at about 2HZ (twice a second). This is my first Nordic/Zephyr project, so I...
Hi
I'm working with an nrf52840-dk on NCS 1.8.0.
I'm attempting to interface the board with an LS7366R quadrature counter over SPI; however, I'm not receiving any count...
hello Nordic
i am using ppk2 pca63100,
working on linux (manjaro), installed the nrfConnect v3.9.3 with power profiler v3.3.0
1. when i connect a device i have to...
This question relates to the unsatisfying reponse to ticket 283390.
The technology of the processor is not important. Arm Cortex processors are as fine as several others...
I am having trouble setting up a GPIO pin that will toggle when the radio is active on the network core. I have tried adding the code in bluetooth.c from the ppi_trace sample...
Hi everyone!
I am developing a board using a nrf52 as a BLE interface for an arduino. My idea in the future is update the firmware of the Nrf52 with OTA. But i wanna do...
Hello everyone. I am trying to set up a BLE central-peripheral network using nrf52840 based on NUS service. I need up to more than 10 peripherals which is customized board...
Hello there,
I'm trying to make a transceiver simulation on nRF24L01+ using Simulink. The block diagram provided in the documentation/datasheet was not clear enough for...
To create the prototype of a computer, which follows a non-von-Neumann-architecture, I am looking for an "Building Kit", which allows non-standard connections between computer...
Hi,
I'm trying to build my own "auto sleep" mechanism based on timers.
This is my code:
The timer works as expected, but when the soft_sleep function is reached, the...
We have a device that we are trying to implement an encrypted data transfer on. We wanted to lock down all the characteristics until we write a passkey on our security characteristic...
Hi there, I am trying to change the transmission power of the NRF5340 devices (for IEEE 802.15.4 radio) with Contiki-NG. With some other hardware (sky motes) that is based...
