This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hi Nordic,
I am using one NRF52840 named A chip(DCDC mode) to provide VDD power supply to another NRF52840 named B.
A is using VDDH with battery 4.2V power supply.
B...
Hi,
I am using nrf5340 kit. I would like to enable and test power management in mesh chat example.
1. Can you please tell me the usage of below config file usage.
#define...
Using: NRF52840, SDK 14.2, S140
My GPIO initialization code is as follows. This is the first thing that happens in main.c.
Here are logic analyzer traces of 2 GPIOs...
Hi
We would like to adjust the pin matching of our nRF52805 design since the measured S11 coefficients in Tx mode are not very good (well above -3dB). The values for the...
Hi.
I am testing a wearable device based on nRF52832 and it does not have a reboot button.
Sometimes the device gets stuck and does not appear on Bluetooth scans. Rebooting...
Hello, I'm in Zephyr OS build v2.3.0 and NCS v1.3.0. I need to reprogram UART0 baudrate at run time to 38400. After having obtained the uart node
uart = device_get_binding...
I want to transmit UART and Bluetooth through 12bit ADC 12k sampling.
I downloaded the following example and verified the ADC-UART AND Bluetooth communication. https://github...
Hi,
I use the nRF52840 chip, which is designed as a module.
I use nRF9160 DK to burn the hex file.
1.And i can use nRF connect to read the ic of the module.
But...
Hi there, We're using SDK 16.0.0_98a98e2. Our setup is a PC running BLE Central connecting to 2 nRF 52840 running as BLE peripherals. We use the provided BLE UART example...
Dir Sir or Madam,
I defined 2 properties in sensor_server mesh example,
Precise Present Ambient Temperature (0x0075) and Present Indoor Relative Humidity (0x00A7) ,
...
Hi,
I use sd system power off to go into sleep mode. I wake up with the help of a button. However, the 1 second wake up time is too much for us. Do we have a chance to set...
I am currently trying to send indefinitely large files over BLE. To do this I have a central and peripheral application running between 2 nRF52840's (one peripheral, one central...
Hi,
NRF52832, SD S132 7.0.1, SDK16, custom device, custom SW
The: custom device not bonded.
In my firmware I can run beaconing in parallel with connectivity advertisement...
