We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi Nordic Team,
I have a installed version of Segger Embedded Studio with both the normal version , and the "Nordic Edition".
When i build a sample project with nRF connect...
Hello，
Purpose: Adjust 5340 frequency offset.
I want to use software adjust the internal load capacitance, but I don't know how to do it.
I found this below.
Can...
In a project using NRF52832 and SDK V15.3, we're having random crashes which have been isolated to a NRF_ERROR_BUSY (17) in components/libraries/log/src/nrf_log_backend_uart...
Hi, I am trying to do unit testing of my application, but at the moment I am not able even to compile and run a test of the example. I am using ncs v1.1.0 following this example...
I downloaded the following repo from github: https://github.com/NordicPlayground/ncs-display-ble-example , applyed the patch and i uploaded the scketch to my nRF5340DK , but...
Good Afternoon, I recently got an nRF5340 PDK kit and would like to get OpenThread examples for this board.
If possible I would like to demo the OpenThread CLI example....
I'm using this code to handle interrupt and power down the device. However, this code is not working the softdevice.
I just want to power on and power off using an interrupt...
Hello,
I am working with the nrf_cli_ble_uart (SDK16), I am able to connect, exchange data, however when I disconnect I got an assert :
It is indeed in ble_nus.c ...
Hi Nordic Team,
I am using a simple GPIO (tx/rx controlled via GPIO) FEM (PA/LNA) with connected to nRF52840.
I know I am allowed to crank up the TX power of nRF to +2dBm...
Is there support in NCS for MCUboot images encrypted with a different encryption key (not the same key as the signing key)? How is that configured (via prj.conf, etc)?
Hi, I have a nRF5340 based target board running SMP server plus MCUmgr. My ultimate goal is to reproduce on Windows the DFU over serial I already do from Linux. Tese are the...
Im trying to interface ADXL345 with nrf52DK via I2C. Im using the reference drivers in below link
https://devzone.nordicsemi.com/f/nordic-q-a/40822/adxl345-and-nrf52832...
Hello,
I am trying to connect a BLE HRM strap with nrf52382 using example/ble_central/ble_app_hrs_c/pca10040/s132
I am getting this on debug
<info> app_timer: RTC...
Hi,
I am having issues programming my custom nRF5340 board and was hoping to get some advice on the issue.
When programming using nRF Connect for Desktop (Windows 10,...
