This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hi
I heard in the "nRF Connect SDK" presentation from May 2020, that the nrfSDK only support BT 5.0.
Is this still correct that the features of BT5.1 and BT5.2 are not...
Hello,
I want to use RAM to keep some data after a soft reset, so that I can find problems after reset. And I also found some implementation methods, such as using .non_init...
Hi so I ran this example:
https://devzone.nordicsemi.com/f/nordic-q-a/40476/unable-to-convert-to-long-range-after-looking-at-umpteen-examples--/157426#157426
When I went...
I need BLE sniffer and I puchase this device because in this manual of "nRF Sniffer" say that "nRF52840 Development Kit (PCA10056) " is compatible.
https://infocenter...
Hi,
Looking at the footprint you supply for the aQFN73 package (I have looked at the one supplied for nRF52840), I see that the pad have a size = 0.275mm. If IPC-7351 is...
Hello,
We have a product that sends out an ESB message approximately ever second, it does this using the RTC timer with the following setting:
It sends the message...
We want to add the nRF52805 to an existing product but also want to have the option to perform a firmware update.
The current DFU implementation doesn't allow the softdevice...
Dear friend Through github: github.com/.../v6.0.1 downloaded nrfutil.exe windows executable file, it can run perfectly on windows 64 bit. However, it will prompt incompatibility...
Hi, all,
I am working on nRF52832 using pc-ble-driver-py bindings to interface my BLE peripheral. Now I want to build the BLE communication between one central to multi...
Hi
AFter setting the switch sw5 to nRF91, itried to update the firmware using nRF connect V3.4.2
I got the following Error
Error while probing devices: Error occured...
Hello,
The Power Profiler Kit(PPK) is not able to measure current consumption. I got this notification asking to reprogrammed the device, I clicked yes and then-after it...
Hi All,
I am currently in the process of designing the PAB layout for my design. My schematic follows the reference design 4 recommended by Nordic.
In this VDD_HV (From...
Device: nRF52832
SoftDevice: S132, 7.0.1
SDK: 16.0.0
I want change DEVICE_NAME by nRF Connect APP, then I add below code, but I found it die here "wait_for_flash_ready...
Hi everyone,
I am working on a project where I have to enter the system into System OFF mode and RAM retention. What I actually want is to retain the value of some variables...
