I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi,
i have designed my custom hardware using BMD-301
i'm able to upload code in bmd-301 using segger embedded studio.
after code uploaded device is not broadcasting...
Hi team, I faced the following problem: there is a custom board with nRF52810 on it, UART is used on this board.
I set up Debug configuration and UART is working OK, but...
Hi,
I am working on a project where I need to send and receive ASCII strings from my Central Device to the Peripheral Device. Before the communication starts there should...
Hi, we have an nRF9160DK (0.8.3) and it does not connect to the nrfcloud.
We have updated to the latest firmware 1.0.0
We only have nb-iot here so we didn't use the iBasis...
Hi Guys
I need your advice. I have a customer that is currently in production with the NRF52840 . They now require direction finding but need a Nordic Evaluation kit to...
Hello,
I am new to Nordic platform, previously i had worked on TI controller.
I have three questions to ask:
1) My firmware consists of four services, each service...
hi,
I am using nRF52832 with KEIL. I want to use version6.0.0 softdevice, but I can't select from KEIL runtime library.
Also, the version that can be downloaded from...
I am trying to change after 10 seconds into non-connectable mode. I am using the below code for initializing:
I want to change mode into non-connectable using this type...
When I use dfu_nrf52832_xxAA_s132_6.1.1.hex, it works all devices updated with blink code as described in dfu_quick_start.md But without any provisioning Process, why? And...
Firstly , I have 2 phone. Phone A is huwawei using android 7 and Phone B xiaomi pocophone using android 9.
Phone A already success connect using UART. But I want to try...
I have a same question:
https://devzone.nordicsemi.com/f/nordic-q-a/22025/in-nrf52840-not-able-to-program-boot-loader-hex-is-using-nrfgo-studio/86420#86420
But I not working...
Hi, I am trying to run the following demo here: https://github.com/NordicPlayground/nRF52-ble-long-range-demo
I have followed the instructions and copied the demo folders...
In my understanding, only Nordic NRF Connect (Android and iOS) can be used to bootload a device using the Nordic DFU.
Is there a corresponding command line tool to perform...
I followed the issues from https://devzone.nordicsemi.com/f/nordic-q-a/54149/error-by-loading-solution-on-ses, which fixed the zephyr script issues, but was seeing the same...
