This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hi,
After reading the nRF24L01 documentation, I have some questions regarding page 66 of the documentation ( https://infocenter.nordicsemi.com/pdf/nRF24L01P_PS_v1.0.pdf...
Hello,
Has anybody achieved to perform Mesh DFU over serial on a Raspberry Pi using nrfutil?
I can successfully perform it on Windows 7/10 (intel) so far with no problems...
Hi All,
I am running a modified example of the 'ble_app_multilink_central_pca10056_s140' project.... I am running this on a PCA10059 dongle. The project connects fine to...
I am getting following error while building the project.
undefined reference to `nrf_drv_timer_pause'
undefined reference to `nrf_drv_timer_clear'
I believe these...
I have uploaded the AT CLIENT firmware and I have connected my nRF9160 dk to my apn, but I don't find any type of AT commend to set a socket and open a port to send and receive...
Hi,
If fires multiple generic_onoff_client set LED = True command from PyACI libraries with Ack = True to multiple nodes, the generic_onoff_client will provide a "generic_on_off_status_handler...
Hi sir,
I want to know if nRF9160 is programmable or not, like other wireless microcontrollers i.e nRF51/52 and ESP32 etc.
If it is programmable, where can we find the...
Hi,
Can we do DFU-OTA on nRF52810 controller ? why i am asking this is , when i saw a video about DFU-OTA they saying that only the controller having at least 32 kB RAM...
Hi,
I would like to know if the access address of the advertising physical channel is affected by this Errata. As far as I understand it is not affected by Errata 107. ...
Hi,
I have developed custom nrf52832 board without external low frequency clock source.
So with that configuration I got problem when try to connect it through nRF MESH...
Hi.
I use Thingy52 B'd.
I want integrate Mesh into Thingy52 Full service demo.
I tested and merge nrf5SDKforMeshv310src/examples/sdk_coexist/ble_app_uart_coexist and...
nRf connect - When updated form v2.6.0 to v2.7.0 the terminal window of LTE Link monitor stops working. No debug info - No AT commands. The same time the Programmer App is...
Hi,
I have a question regarding NFC OOB pairing (SDK version 15.2):
I am using "nfc_ble_pair_init" with PAIRING_MODE_OOB. This works when I touch nfc with my mobile. I...
Hi, guys. I'm trying to create a custom 4-layered 1.6mm thick FR-4 PCB which uses the NRF52840-QIAA-R.
It's my first time using the nRF52840 so I have some questions, please...
