But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
I am trying to measure the power consumption when transmitting data from an external device to nRF 52832 to a smartphone.
I am trying to measure the power consumption of...
Dear, I'm designing a PCB with nRF52832 and I will intend to use DCDC converter therefore I putted the two inductors (10uH and 15nH) between DCC and DEC4 pins. The same hardware...
Hi,
I am developing a project in IAR Embedded Workbench for nRF52840-Preview-DK. I have integrated different modules (ble, ADC, SPI, I2C) in this project. I don't have...
I like to integrate the nRF54XXX with a LNA/PA combo (skyworks RFX2401C or 66110). Could you please tell me which pin should be used to control the RFX2401C TX/RX? Which has...
Hello all,
I am currently working on a project to control a door lock and use ble_app_multirole_lesc as reference.
As measurement the current consumption is around 6.5mA...
Hi, I’m working on low power wireless sensor network. I have a big dilemma in choose of wireless mesh solution. Maybe firstly, what i need: 1. Support for low power devices...
Dear all,
I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the static key feature. But every time when I configure the static key including letters...
Dear all,
I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the static key feature. But every time when I configure the static key including letters...
Hi,
I am trying to connect to a device while service discovery for another device is running, this is needed to go through connecting multiple devices as fast as possible...
Hi
I am using the light controller and added zb_nlme_permit_joining_request to allowing devices to join the network.
I get a good ZB_ZDO_SIGNAL_DEVICE_ANNCE signal and...
In mesh2.1.1\examples\light_switch\proxy_server I find this flash_manager.c file.Its purpose is to store/resorre/remove DSM&access data.
My flash function referred to access...
Dear Team,
I hope you are doing good......
i am using nrf51822 Device, the SDK version is 12.3.0 in the windows pc with keil version 5.26.
Here i am planning to send...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Hi everyone!
I have BMD-300 Series Evaluation kit featuring the nRF52832 and dongle(nrf52840).
I want to use ‘ComPortMaster’ program to process the received data via...
Hi,
I am Using NRF52840-DK. I merged the UART Example code (PCA10056) into the nRFX_SPIM (PCA10056) example code. That compile successfully I want to print a simple statement...