Hi...
When i was working in SDK v6.1.0 i have tried nrfprog.exe to merge and program bootloader, softdevice, application and bootloader_settings file as explained in devzone...
But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
Hi I have a urgent production problem about the Nrf5340 chip.
In all my pre production, I use nrf5340DK to program my designed board using the jlink through jtag 10pin cable...
Hi,
I want to confirm that on the nrf9160, for pin assignments, any pin can be assigned to any peripheral (instantiation)?
So it doesn't matter what of the available...
If you have tested the nRF9151's GPS with the CMW100 or IQ station. We need to know: 1. What test waveform file is required? 2. Should we use the ARB file or the CW waveform...
I'm trying to experiment with Bluetooth Channel Sounding using the nRF Toolbox App with an nRF54L15-DK. The app is running on a Google Pixel 10 running Android 16 QPR3 Beta...
From: https://github.com/zephyrproject-rtos/zephyr/issues/103807 Describe the bug
Hello,
I have configured a project based on the nRF5340 DK board and added a debounce...
Hi, So, I want to do BLE DFU from one nRF52 MCU to another nRF52 MCU. The start point for me was this:
put SMP server sample on one nrf52dk (this device is advertising...
Hi
I am using the ESB sample and want to use the RADIO_MODE_MODE_Nrf_250Kbit PHY, but I will get not support after requiring:
Can we still use 250 PHY in nRF54L15 ESB...
Hi,
After upgrading from NCS 2.5.2 to NCS 3.1.1, I get quite frequent MPSL assertion errors on a nRF52840. Can you shed some light into what this assertion error is about...
The datasheet list
A25, B12, B26, D2, F2, G1, H2, J31, K2, T2, AG31, as N.C.
I have not been able to read exactly what N.C. implies: It could be: "do not connect", "no...
Hello,
I am working a project that uses the NRF52840 dongle with BLE and UART to communicate to two separate devices while going through temperature cycles. I have not...
My device supports both Central and Peripheral roles. By default, it works in Peripheral mode. When the device connects in Peripheral mode, I want the following behavior:...
Hello Nordic team,
I am working on an nRF52840 project using nRF Connect SDK (Zephyr-based, v2.x / v3.x) and I would like to clarify the official support status of a specific...
Running doxygen nrfx.doxyfile
Per the README.md in C:\ncs\nrf-bm\v1.0.0\modules\hal\nordic\nrfx\doc fails.
See output below.
C:\> C:\apps\doxygen-1.16.1.windows.x64...
Hi there.
we have firmware that was running on nRF5340 MCU. we had decided to migrate to the nRF54H20 MCU because of flash size limitation. this MCU was announced with 2MB...
I am trying to connect to two reflectors and sound only from 1 device so far the connection and soundnig works well for first set of connection and after a disconnectio, the...
