This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hi,
I'm working with UART with DMA(UARTE) on nRF52840. UART does not have HW flow control, just RX-TX.
I'm confused with DMA part. Is DMA circular or I have to reset it...
I have a nRF5340 using nrf connect v3.7.99-nc1 that is in a peripheral role. I establish a l2cap connection to the peripheral, to request a larger amount of data. That works...
Hi,
Working on a new project, custom board, using an nRF52840. Wrote my own DTS and all that. Program works as intended, but the nRF Connect for VS Code plugin refuses to...
Hello,
I am using nrf5340 audio sample with the custom board. The nRF Connect SDK version I used is v2.7.0.
I referred to this post and tried to add skyworks fem to my...
Hello,
I am working on using the Nordic nRF TNEP API to support an NFC Bluetooth tap-to-pair application with negotiated handover. I have been working on programming the...
I'm working on custom test software for use in production programming/testing of my product containing a nRF9160. I'm using the nrfjprog executable, but with problems, every...
Hello. It's not charging at npm1300. The manufactured circuit did not have cc1 and cc2 of usbc connected to cc1 and cc2 of npm1300. If cc1 and cc2 are not connected, does...
I saw the recent announcements on your LinkedIn, that you're partnering with various NTN providers, that allow one to use LTE over NTN. However, how exactly do I access these...
I have a multithreaded application running on NCS 2.9.0 and I want to be able to see what all the threads are doing at the time of a crash via coredump. I have the following...
Hello team,
We are using nrf52dk with nrf52832 by vs code nrf connect sdk extension.
I have add zephyr led blinky application and flash it on the board and it's working...
Hi,
I like to analyze my custom BLE firmware thread activity, event, and timing using the Segger SystemView application. I have added the following configuration in prj...
Hello,
A super-simple piece of code that enables UARTE1 to receive a byte stream does not seem to work.
It seems as if nrfx_uarte_rx_enable() hangs up.
When I single...
I wanted to check if iOS 18 supports extended advertisements on coded PHY. I am not concerned with the advertisement payload limit but the increase in range that is possible...
I tryed to use the callback function provided by mgmt to hookit, but after including the header file` zephyr/mgmt/mcumgr/grp/img_mgmt/img_mgmt.h `, it prompted that "mcuboot_config...
