Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
Hi,
I need to use system tick to do some math calculate. So I create a new function to get systick like as below. then I can get some number.
And I create a 200ms timer...
Hi,
I'm new with BLE development and I'm trying to find a module that can be used with an Atmega328p and libraries that allow me to create a GATT profile (creating services...
Hello, everyone.
I'm beginner at this, and I need your help.
As the title says, which of the GPIO pins can be specified for PWM?
I am waiting for your answer.
Dear Members,
I want to run :
E:\nRF5_SDK_17.0.2_d674dde\examples\peripheral\spi\main.c
on this line :
APP_ERROR_CHECK(NRF_LOG_INIT(NULL));
I get :
error ...
Hello, I have an application using nRF5 SDK 17.0.2 and SoftDevice S140, I would like to implement the mesh function on my devices and I have some doubts.
1- What is the...
I tested it in a conductive way. The transmission power of +8dbm is set on the software. Remove C3 and L1 and connect the RF line directly to the ANT PIN to test the transmitted...
Trying to understand how interrupts work on nRF52: does setting an INTENSET register of the said peripheral enable the interrupt, and to propagate the interrupt over the Cortex...
My operating system is window 7, and I have been using nrfjprog v10.12.2 before. When I updated nrfjprog to v10.15.0, the following error occurred when using nrfjprog -v....
Hi there,
I want to run FATFS example but I got this error ?
========================
nfo> app: FATFS example started. nfo> app: Initializing disk 0 (SDC)... rror> app...
Hello.
I am developing using nrf52832 (S132 v7.0.1, SDK v17.0.0).
I found that the maximum clock frequency of nRF52832 is 64MHz, but I don't know what the current clock...
Hello,
I know there are dozens of threads on this topic already but they don't seem to quite answer all my questions.
Some background:
SDK: 15.2
SoftDevice: s140_nrf52_6...
I am encountering the following error when trying to build the Asset Tracker code. I have tried uninstalling everything and reinstalling it and the issue is still there. I...
nRF52832, SDK 13.0, no Softdevice
I had a possible power leakage issue and tried to debug it with Segger Embedded studio.
Please refer to below.
int main(void) ...
Hi,
(nRF52840)
I have project made in SEGGER Embedded Studio with OPUS Encoder (optimized by Nordic). It's CELT, bitrate 40000 and complexity 5. This is configuration...
