Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi.
I'm trying to generate random numbers in my custom SPM. I couldn't use spm_request_random_number in the secure module (unlike using it in the non-secure module), so...
I am using nRF 5 SDK v 14.2.0. I would like to receive data from smartphones via Bluetooth communication, How do I program? I would like to have a professor. Sorry to trouble...
Hello,
i want to use Seggers RTT on os X (nrf52832). I followed the Tutorial and i compiled and upload with success. But if i start JLinkRTTClient on my mac nothing happens...
Hi
I'm looking for a Dev Kit that replaces the nRF51822 kit in the link below.
https://www.digikey.co.uk/en/product-highlight/n/nordic-semi/nrf51822-bluetooth-smart...
Hello,
We are trying to read a received RSSI value from bluetooth mesh opcode handler however it does not relay this value to the callback.
Callback is added here...
Hi,
I just got a nRF 5340DK (PCA10095, 1.0.0 2021.9) which doesn't show up on my windows 10 computer.
When I connect it to my computer, the green Led 5 blinks rapidly...
Hello! I am a beginner at nrf programming and have just started using the NCS and Zephyr on an nrf5340 evaluation board. I understand that Zephyr seems to be more or less...
I'm using a nrf52810 with limited flash size especially after adding a UART bootloader DFU and S112. I added uECC for connecting security. Now I need AES128 for my own application...
Hi,
I'd need some information I'm not able to find in product specification v1.3:
What is the architecture of the GPIO / AN pins of this device? Input p rotection diodes...
Hello,
I have successfully programmed the ble_app_uart example to a custom PCB using the 52832. Here is the board schematic, on the board C15 and C16 are not fitted.
...
Hi,
I want to know is Liniux system supported Nordic BLE OTA DFU ? According to official documents： https://www.nordicsemi.com/Products/Development-tools/nRF-Util ，it just...
Hello community,
I am implementing BLE peripheral code contains, A custom service, characteristic.
I am referring this link : github.com/.../custom_ble_service_example...
Hello, nrf5340 datasheet -> nRF5340_OPS_v0.5
section: 7.1.26.7 Sending custom instructions (Page: 383) 1. we can send an instruction consisting of a one-byte opcode and...
I kind off trying enable TWI in bootloader mode, This is because of following reasons.
Firmware is stuck in bootloader, if somebody removes the Device Battery during...
