After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
Hi :
We create UART Over BLE service on NRF52832 SoC. It worked fine used SoftDevice V2.0.
Now update SoftDevice to V7.2.0. got this issue. where can i found SoftDevice...
I'm trying to drive the RGB LED light on the Thingy:91. So far, I've not been successful. I was hoping that by listing the steps I perform I might be able to get some advice...
Hi,rotocol
In Nordic's Smart Remote 3, it is mentioned that IR transmitter is protocol agnostics while IR driver is Protocol specific. Is it possible to write a common IR...
Hi,
Is there any battery life calculations for NRF52 and NRF51 (Beacon)?
For example: if TX power of NRF52 is 0 dBm and it broadcast every 5 seconds ? Or with any other...
Hello
I am working with nRF5340 and made the project according to "the first step to build". I want to add some libraries to my project but I can not. The libraries I want...
Hello, I am using MX25R1635FZUIL0 with nrf52 and my device is working with freertos. I have three different tasks using/accessing the flash functions but when i read back...
I use nRF52840 to creat a project. IDE select SEGGER. before everything is normal. when I update the SEGGER TO 5.42 version. i build the same project. there is one error.Please...
Hello, according to the latest nrf5 SDK documentation, the nrfx_gpiote_init function takes no argument, but if I call nrfx_gpiote_init() in a zephyr application, I get the...
To reproduce this problemm Ive added a device to the I2C that does not respond to a read command. The `i2c_read` call first returns `-EOI` (-5) and for every other i2c funcion...
The device nRF52832 cannot connect over SWD and generates the following error.
- Connecting via USB to J-Link device 0 - J-Link firmware: J-Link EDU Mini V1 compiled Apr...
After configuring the options for an nRF project, segger studio cannot create the project by warning me the error: "create_nordic_project.py failed"
The problem seems to...
I'm trying to make MQTT publisher example work using a BMD-340 evaluation board and nRF5 SDK for Thread and Zigbee 4.1.0 . I'm using a Raspberry Pi 3B with a Raspberry Pi...
Hi,
We have been using the MQTT sample code with a few iBasis SIM cards for some time without issue. This week we made a test where the mqtt_disconnect function in the sample...
I got the BLE mesh SDK from: http://www.nordicsemi.com/eng/Products/Bluetooth-low-energy/nRF5-SDK-for-Mesh/(language)/eng-GB
I want to develop a mesh gateway to connect...
