After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
where can i search whta the mean about <type>,<result>,<datatype>,,<qos>,<retain>.....Etc.
EX: #XMQTTEVT: 4,0
I Don't know what these values represent
thanks
...
Hi,
We're using a 51422 with s130 to perform OTA DFU.
Both bases for bootloader and central are from sdk 12.2.
We have already implemented the older DFU (non-secure...
Hi,
I want to use the Code Profiling feature from Ozone with my nRF 52840 DK and the j-Trace Pro Cortex. Compiling and debugging my program works flawless inside Segger...
I am trying to figure out how to use the TX part of the BLE NUS Service to send a notification. Currently I am receiving data via the nus_data_handler, however because i will...
Hi, I just got my nRF5340 PDK and was wondering if it is possible to develop applications for the nRF5340 PDK in the Keil IDE?
I have been reading on the site and trough...
Normally with Segger Embedded Studio if you want to do a command-line build you use embuild.exe instead of emstudio.exe and away you go.
However, the NRF Connect/Zephyr...
Hi
We searched a lot of stuff regarding FOTA update in nRF52840DK using Lwm2m and coap protocol. But we could not get help in the right direction. We could not find any...
Hi,
We are using today SDK 15.0 and are upgrading to SDK 17.0 for development of our system.
In our application, we use BLE communication.
While comparing SDK_config...
I'm now using HX711 50kg sensors to build a scale
Now I can read the data from HX711, and try some method from internet, but still can't get the real weight
does anybody...
KeyWords: nRF52832 ESB Flash as EEPROM SDK:17.0.0
Hello, I an using nRF52832 developing ESB communicution with other nordic product.
I need to save some infomation, so...
Hi,
I got today a sample of your Nordic Thingy 91 device. I like to integrate the device into our IoT Data Provisioning Service from IoT Creators (Deutsche Telekom IoT...
Hi Everyone
I am able to write and read to and from QSPI memory interfaced with nrf52840 PDK.
I am using Segger Embedded Studio with sdk15.0.
I want to create a text...
If I write a value to ERASEPROTECT.DISABLE -- which itself works, as I'm fully able to perform the mass erase by writing the same value using the debugger -- I can't seem...
Hi,
We are using NRF52833 as a BLE central in our latest product and is undergoing radio certification tests. We are using SDK16 Radio Test example for the tests.
...
