This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I m bonding a central and a peripheral and saving the bonds into a whitelist i use at each startup. When i delete the bonds on central side, the connection to the...
I am using a ultra-miniature (BMD-350) series module from Rigdo which has the nRF52832 BLE SoC. The pins from the nrf52 SoC are all brought out on a female headers on a custom...
I am running a custom board (Ublox Neo dev board) and have a custom board file.
I have modified and and can run code in Segger Embedded Studio based on the peripheral serial...
Hi,
I'm getting a Hardfault MemManage (IPSR 003) when calling sd_ble_gap_adv_stop(). The advertising handle I'm passing is 0. This is called after the advertising has started...
Hi!
I use the peripheral blinky example from the sdk v15.0.0. I ave added some code so that the board is scanning for advertising messages aswell. Every thing works fine...
Hi,
I've just realized the project from
https://github.com/Martinsbl/nrf5-mpu-examples/tree/master/nrf52-mpu-easydma-using-gpiote-and-registers
And it is working quiet...
Hello everyone, I am trying to send and receive messages over UART using Teraterm, the PCA10059 dongle and the UART Android app.
I was following the directions found in...
When I was trying to update the modem firmware, it showed something like this...
Traceback (most recent call last): File "c:\python37\lib\runpy.py", line 193, in _run_module_as_main...
Hi,
I am working on increase data throughput between phone and nrf52832. I am using SDK 15.3.
I create a service and a notify characteristic. I am sending 20-byte packet...
I currently have a hobby product that reads sensors and turns on/off relays based on that sensor input. I've got an nRF52840 that sits on my sensors and relays, and I have...
Hi,
I am working on nRF52832 with MAX30205 temperature sensor , i am comparing the temperature with threshold value like this if (m_sample <threshold) then send the data...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
In my application, I am starting BLE advertisement...
Hi,
I'm trying to include AES256 CTR in the ble_app_template project.
What i've done so far: .c files:
- Included the files from /components/libraries/crypto
...
The time to first fix on the Development Board (as well as a prototype PCB I have made) are both around 2 minutes. After getting a fix, is any of the almanac or ephemeris...
Greetings. Is there a way to do information mapping using, for instance, one of the mesh nodes that could act as a client/provisioner to all other nodes and therefore keep...