We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
I wnat to set P0.30 and P0.31 for I2C CLK and SDA. nrf_drv_gpiote_out_config_t out_config = GPIOTE_CONFIG_OUT_SIMPLE(false); err_code = nrf_drv_gpiote_out_init(30, &out_config1...
I set up my nrf52 self board with internal LDO using reference schematics with internal LDO setup.
Im entering the power safe mode using __WFE instruction
Also i did...
1.I used Timer2 Capture function Time Frequency is 1MHz. Picture1 Current counter should be 33330. Picture2 Current counter should be 5000. Picture3 Current counter should...
Hello,
I am having an issue with setting up the event generation timing on the nRF51822. Long story short, I am configuring Timer/Counter 0 to generate an event every 50ms...
Hello,
I am using NRF51 DK for developing an application. I tried running the default SPI example in the SDK 12.3 which uses the spi and spis example. The location of those...
Issue exists in SDK 15.0 and probably many many others...
I noticed that the nrf_log_push parameter is indicating it must be a constant pointer to a mutable character...
I'm attempting to pull the mesh bootloader out of the sdk and put it in its own makefile project, so it can be built separately.
I'm building with `gcc-arm-none-eabi-7-2017...
Hello,
I want to achieve bidirectional data communication between one central and two peripherals. Any my central device should be able to do bi-directional communication...
Hi. I have been looking through the forum to find anything that could answer my problem, but can't seem to find it. I am working a project, where our needs is to use a nrf52...
Hi there ...
In Softdevice S140 v6.1.0 started supporting advertising extension with this macro "BLE_GAP_ADV_SET_DATA_SIZE_EXTENDED_MAX_SUPPORTED" and I follow the migration...
Hi Team,
I am using nrf51822 for my project, i have connected a PIR Sensor and a push button also a LED driver WS2811 .
I am using ble app uart example as i have to control...
Hello,
I'm looking for 3D STEP model of nRF52840 QIAA aQFN73 package. I just found step model of dev kit, but not component itself. Could anyone help me and share one. ...
Hi,
I was trying to follow the steps for this example: https://github.com/NordicPlayground/Nordic-Thingy52-mesh-demo
However, I reached step 5, where I should compile...
Hi,
I am developing a bootloader for a custom board with the nRF52840 (nRF5 SDK v15.0.0 and SEGGER Embedded Studio V3.30) where we have no other option but to engage DFU...
