Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
First of all, I see that NRF52840 doesn't have a Real Time Clock but it has a Real Time Counter which is not working in case of sleep and low power mode, am I correct?
Second...
Hey everyone,
I am having trouble setting up the lsm6dsv16x as a interrupt. I was able to successfully poll the data meaning I can talk and read imu data, but no interrupt...
Hi , I wanna keep my existing mobile application which talks to nRF5340 over the BLE NUS service. I am using the default BT_UUID_NUS_VAL as my primary mode of communication...
I want to edit the explom firmware that comes with thingy91 to add the reading of new sensors and send them to nrf cloud. Where can I get the example of the Asset Tracker...
I have a custom board that started life based off of RF9160-DK 1.1.0.
We have a single programming header that can be used to program either the 52840 or the 9160 depending...
I've installed nRF Connect for VS Code Extension Pack v2024.9.5 to ubuntu 22.04 and after opening vscode the free disk space continues to diminish and cpu load is constantly...
Hello,
We are working on an integration between a nRF52832 and ST LIS3DH accelerometer on our custom board, using SDK 15.2.0 with SoftDevice and BLE enabled, and have observed...
The last couple of months I have been following the course “nRF Connect SDK Fundamentals”, but I am unable to get further than Exercise 2. This is because Visual Studio cannot...
Hello,
I’m having issues with time synchronization when using the sidewalk Sub-GHz template from SDK v2.5.0. My setup includes a Nordic Semiconductor chip nrf52840 and LR1110...
What is the reason for the default 320 hour setting for periodic Tau timer? This seems like an awfully long time, and we're wondering if this is simply a placeholder, or if...
Hi. I'm finally bought a PPK2 to test some of self-built IoT devices. I do have a question in regard to the device (before I break anything). Does it offer any types of short...
Hi. I tried using the TWI master and slave drivers on 2 different nRF52840DK boards. The 100KHz frequency is perhaps a little high and I will see how to lower it by acting...
HI ALL,
I want to create a static library in the application layer, but this library will contain nrf related header files, which will cause cmake to not compile properly...
We have a custom board based on the nRF52805 and we're seeing some odd behaviors in debugging / testing that we're trying to nail down. Two questions:
The INFO.VARIANT...
When I use the J-link programming program, the following happens to the J-flash connection chip
SEGGER J-Link Commander V7.67d (Compiled Jul 5 2022 16:15:35) DLL version...
