Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
I am working on zigbee network.
I have seen that there is an event for network joining but could not find any event for network disconnection.
If I want to check that...
Hi
For a low power product, I need the nRF54L15 to wake up periodically with very low consumption in between. In the deepest sleep mode there is no RAM retained and so the...
So I've been trying out the nRF9161DK, and had a lot of problems creating builds with the included samples. Mostly CMAKE errors.
Guess I'm missing some basic knowledge here...
As shown in the figure above, if I need to modify the time interval of OpenThread's Link request or parent request, how can I do it? Thank you
NCS 2.6.0
NRF52840
Hi I am trying to add multiple services to the custom_ble_service tutorial example right now. When I try to create a second ble_cus_t instance 'mcus2' by calling BLE_CUS_DEF...
When I set CONFIG_BT_FIXED_PASSKEY=y in prj.conf. The following warning messages are generated by west build command.
CONFIG_BT_FIXED_PASSKEY is enabled
A fixed passkey...
I'm trying out to operate an external flash and first thing to try before anything was the spi_flash sample.
*** Booting nRF Connect SDK v2.8.0-a2386bfc8401 *** *** Using...
I have a question about tasks with different priorities and interrupts.
So for example I am using I2C and UART with different tasks and suppose I2C is in the midst of transaction...
Hi all,
We are working on a project that uses the nRF5340 and nRF7002 combo. In our application, the device enters a low-power mode on the nRF5340 during sleep, with the...
Hi,
As the subject, when i connect to the Windows with the cable connected with VDD side, it will not show up Jlink in Windows.
What should I do to reset the Nrf5340 ...
Hey everyone, I am looking for big size capacitive touchscreen for my next project so I do found with resisitve touch using FT810 EVE graphic controller with nrf52840( https...
I was trying to get a simple Zephyr project to build and run on the Arduino Nano BLE 33 which has a NRF5248.
In VSCode with the NRF plugin I select "Add build configuration...
I have a PCA10056 (nRF52840 DK) and while programming it with a UART example from the nRF5_SDK_17.1.0_ddde560 using Segger Embedded Studio for Arm 5.42a, it will not show...
Hello, I have one smartphone with Android and one ith iOS with NRF connect application and I can't see, only on iOS, the Primary and secondary PHY used by my advertiser device...
