After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
Hi,
I just got a power profiler kit II and I want to use it in an battery based application, where there is also the possibility that current will flow in the opposite direction...
I am using the nRF54L10 chip with NSC-V3.0.0, and I encounter an issue when using uart21 (p2.07–p2.08). If RTT is connected, UART transmission and reception both work normally...
Why doesn't the scan_evt_handler get called in the ble_app_uart_c sample under nRF5_SDK_17.0.2_d674dde conditions? I've tried various things, but neither scan_evt_handler...
Hi,
We are testing a custom board based on the nRF5340 that drives an RGB LED strip using the TI TLC5947 LED driver.
The TLC5947 has an OE (Blank) pin that disables/enables...
Hello,
I am using an nRF52833 in a project where and i want to be able to update it via another mcu (STM32H7) over uart. The STM32 has received and saved the new hex file...
Hi, I have a custom NRF52840 board that I need to send EMG data via BLE with. Only has SWD, no usb-c data link unfortunately.
I am using version 1.6.1 of Adafruit NRF52...
I was reading the Errata document for the NRF54L15, and came across this: 3.18 [37] POWER: Current consumption might increase after pin reset or power cycle. So I was wondering...
I'm testing the NRF54L15 radio and found an issue. When I set the radio to BLE 2Mbps mode, I received data from adjacent frequency bands. For example, I set the radio's receive...
Dear experts, I am programming bare metal using Segger Embedded Studio and nrf.h and want to achieve a simple example of network core sending data to the application core...
I've been developing firmware for my PCA10059.
I load the package with nrfutil dfu usb-serial --package=_build/t.zip --serial-number=`cat /tmp/serials.txt` --connect-delay...
Hello:
I'm watching the Structuring nRF Connect SDK Projects for Flexibility and Scale webinar. I'm following the hands-on video step by step. When using "Create a New Board...
Hi,
I'm currently facing an issue with my nRF52840 chip acting as the transmitter connected to a BLE broadcasting device. One client uses a voice recorder product that requires...
Hi Support Team
We want to use the J-Link of nRF54L15DK to program customer's nRF54L15 board. We follow the guideline of below link to connect the Pins of P19 of nRF54L15DK...
I am trying to connect waveshare e-paper 4.2" display to my nrf54L15, I am currently running a peripheral uart sample code on the board and my plan is to build the project...
