i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Hi!
There are many questions regarding the high voltage mode of the nRF5340 already in this Q&A, but I don't see the answer to the question, how it is enabled programmatically...
Hello, is it possible to set gpio direction (input/output) from devicetree?
I haven't found any gpio flags to do this in the gpio.h located in dt-bindings folder.
Hi all. The current devices we are developing are made with NRF52832 based on the NRF SDK v16. We also plan to use the Wirepas stack. Initially, we want to implement support...
hi
i have developed my device,and it was work in customs,but there is some device cant work after work some times.we recall the device and discover the firmware was loseed...
Hello,
I have a question regarding GPIO setting during sleep mode.
nRF52832 is sleep and wake-up by GPIO state(Red in below picture).
When Red is high, nRF52832 go...
We are trying to implement errata 254, but I've run into a couple of questions. What's the correct test to see if the device needs the workaround for the errata? NRF_FICR...
Hi, I am using pc-ble-driver v4.1.4 combined with connectivity firmware compiled with s132 v6.1.1. My application is running on custom hardware with a cp210x serial to usb...
Hi, i made some research on the VMA323 sensor, how to get it to work with my Nrf5340dk but i didn't find any documentation is there any available documentation about this...
Hello sir,
I am using nrf52832 Dev board and write the value '1' through nrf connect app by enabling the notification enabled with case length one i.e (p_evt_write->len...
//this ticket is a diversion of this ticket @Increment Counter on Button Clicked https://devzone.nordicsemi.com/f/nordic-q-a/82239/increment-counter-on-button-clicked Hello...
Hi,
I have used an NRF9160 in Belgium with the iBasis sim card, connecting via LTE-M and NB-IoT with operators Orange and Proximus. HTTP requests work fine.
However, when...
I'm running nRF Connect Extension Pack on macOS within VS Code
Whenever a Build or Pristine Build has finished the terminal shows this message:
Terminal will be reused...
Dear NCS experts,
Considering a Bluetooth Mesh firmware application based on nRF Connect SDK 1.7.1 that is running on a nRF52832: How do you enable/disable the gatt proxy...
I can't seem to delete my post, but my Common->Preprocessor->User Include Directories path was incorrect (included an extra folder name)! My problem is resolved.
I am...
