Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi，I am trying to use nrf52832 to drive the ad5940 chip, but using the function in the SPIM driver library to initialize the ad5940, I have been unable to get the ID of the...
Hi Nordic,
i'm using a nRF51822 based board (Adafruit Bluefruit LE Sniffer, PRODUCT ID: 2269, https://www.adafruit.com/product/2269 ) and could sucessfully update to nRF...
Hi
Sorry,This case is the following of case ID: 278538, I didn't find a reply button option in case ID: 278538,So I recreate a new case, I failed to create a new application...
Hi. I am trying to get the gsm modem sample project to work with an nRF 5340 app and a Nimbelink LTE modem, NL-SW-LTE-TC4NAG. The only change I made to the project was to...
Hi Nordic Support Team,
First sorry for basic questions.
I'm learning the basic hardware setup & Linux driver configuration things to setup & configure the MCU(i.mx6)...
Hi, i am Agustin.
I am working with Thingy 91. I am using the Asset Tracker V2 application to upload data to AWS. I have a problem with "Build Solution".
Hi , I got a problem when testing nrf53 qspi signal using a logic analyzer ,with a non-blocking init of qspi and a 4 Byte write , codes are below:
I got a word align problem...
Hi Team,
I want to use the Nrf52840-CAKK-R7 chip to fabricate a PCB board. And communicates with other chips by SPI interfaces.
Now, I want to select the GPIO ports by...
Hi All,
I'm using nRF9160DK PCA10090 Version 0.9.0 and I want to update the Cellular Modem Firmware using nRFConnect 3.8.0 Programmer v2.0.0. Debug Probe is switched to...
We have a timer with a number of variably sized intervals as illustrated below operating on a single capture/compare channel (CC):
Currently the method we use to set the...
Dear all,
In the datasheet and online it is mentioned that the DAP (Debug Access Port) is activated when a programmer is attached. Moreover, it can happen that the programmer...
Hello all,
I am trying the get working the example project nfc_writable_ndef_msg on a nRF52832 with the nRF5 SDK.
I have tried the others NFC examples were most are based...
Hi I am trying to update the connection interval of a peripheral device (nRF52840 ) and I have followed the steps mentioned here .
After Enabling the ble on the device I...
Hi Team,
I have several nrf52840 developing boards for developing BLE Mesh applications.
Now, I want to use SPI interfaces. I didn't find any instructions or examples...
