We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi there devs,
### I UPDATED and reformulate the whole question after some finds ####
I am having an issue with my application which is really hard to replicate it could...
Dear,nordic:
Please help me solve the socket communication process encountered in the exception
SDK : ncs v1.2;
samples : asset tracker;
path : ncs\v1.2...
Hi,
I am running a modified version of the light switch example, where I have modified the generic on off model to send byte arrays.
So I have been changing my models...
Environment:
nRF5 SDK version: 17
SoftDevice: S140
Tool: Segger Embedded Studio
Debugger: J-Link EDU Mini
Board: Arduino Nano 33 BLE (Using SWD pins with the J-Link...
SDK 15.2, nrf52840 SD 6.1
I'm having an issue where a reset with RESETREAS DOG 0x02 is not coming through the WDT handler before executing reset. I can force this reset...
Hi,
I have the following application in mind: I want to create a bluetooth mesh network, in which one node will broadcast sensor readings, some nodes will be used to hop...
running sdk version 16 on nrf52833 ,
1. on power on , start advertise - " nrf connect" connected successfully ,
2. disconnect from the "nrf connect" , start advertise...
Hi folks,
I'm trying to find a pcb prototype manufacturer which supports the via-in-pad requirements for the nRF52840 package (i.e. 0.15mm hole size with 0.1mm annular ring...
I'm using the nRF52832, and taking ADC measurements, with 14 bit resolution and with Oversampling disabled. The nRF52832 Product Specification mentions the saadc can be configured...
Hi,
I modified the ble_app_att_mtu_throughput example to scan and advertise simultaneously. I want to have two nRF52’s that can read each other’s advertisements and pull...
Hello,
I have a system composed of one central that needs to 1) briefly connect to many (100+) peripherals, 2) download a small amount of data from each, and then 3) disconnect...
Hello,
I am working with SDK 15.3.0 and the nRF 52832. I am working with the Segger IDE v4.16.
I attempted to load the scripting as instructed in the SDK documentation...
Hi, I had this working, I'm sure of it. Now though I get 100% duty on one channel and 0% on another. Something's not right. Pins are correct, my focus is CFG_PWM_OUTPUT_FRONT_NUM...
Best regards:
Once the data was received in PRX, Is there a way forward (or modify) to PTX the same data and deliver it together with ACK payload in the same transaction...
Hello, i would like to test usb_msc example on a custom board, and i have few questions:
- will this QSPI flash chip work with nRF52840 QSPI interface, and is it sufficient...
