Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi,
I've got a custom board with nrf52832 mcu. I use the nRF5_SDK_16.0.0_98a08e2 with s132_nrf52_7.0.1_softdevice.hex.
Sometimes the app_error_fault_handler is called...
Hi,
I have a project based on the NUS (Nordic Uart Service) example.
I have bought a USB dongle MDBT50Q-RX manufactured by RAYTAC ( https://www.raytac.com/product/ins...
When I tried to send data in the form of float it shows an error and I changed it to another format as sending flag, mantissa(3 bytes), and exponent (1 Byte). Can anyone help...
To the kind attention of Nordic support team,
I have got an nRF52840 working application using usb and gazell, and I'm porting it from nRF52840 to nRF52833 these days. Yes...
I have some nRF52832 devices that have been flashed with a Softdevice v13 based firmware and can receive OTA firmware updates. Unfortunately their enclosures are sealed and...
Hi,
I am attempting to get the adxl362 sample working with the nrf9160 dk board. I am using the nordic SDK v1.2.0. I cannot get it to compile, compiling the code below fails...
Hello,
I am using SDK SDK_15.3.0_59ac345 in application that receives data from UART, and the aplication is running in background just ADV.
In the main function, after...
Sir,
With reference to the subject cited above the undersign is working as Assistant Professor in CSE Department and doing R & D in IOT.
I want to recommend your product...
Hi There,
ISSUE:
New Nordic Thingy:91 will not connect to the LTE network, it is giving:
2020-03-25T18:10:10.221Z DEBUG modem << cloud_connect failed: 22 \x0D\x0A...
Hi,
I'm working around to integrate FreeRTOS to Libuarte example, but i'm getting an error while building the project says:
For the Libuarte instance i'm using RTC instance...
Dear Sir,
I want to do the following scenario.
Once I power the device it will start advertising.
Now the advertising duration is 2minutes.
I have written...
I have a nRF52832 dev board and a separate J-link programmer. I want to do a sanity check on the programmer and I was wandering if there is a way to program the dev board...
I'm studying to perform DFU Peripheral from Central both using nRF52840, I'm able to issue command to let Peripheral into DFU mode, but got a "Received a fault" message in...
Hello,
I am using nRF52832 chip for freeRTOS project and using RTC2. I have SDK15.2. I want to have timestamp from RTC as hex format. I searched almost all forums but i...
