We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi i am using sdk15.3 secure boot-loader example. i had change backend to cc310. without optimization i am able to upgrade code but when i am using optimization level 0 it...
Hi,
I am working on an USB CDC program with nrf52840-mdk-usb-dongle. The PC needs to use a terminal emulator like putty to connect to the dongle. Now I send and recieve...
I use Zigbee CLI example on nRF52840. (examples\zigbee\experimental\cli\cli_agent_router)
It use UART as 115200 bps with CTS/RTS (hardware flow control).
I want to change...
Our product uses non-connectable/undirected advertising, where advertisement packets are sent every 1 minute for 500ms time. For that we are using FreeRTOS timers to start...
1: Is there any information that can be systematically introduced to the production test of Bluetooth products? 2: What parameters do I need to test for mass production of...
Apparently， Config AppKey Update message can be transmitted in the key refresh procedure. However, one point let me very confused, I looked into the Mesh Spec v1.0.1 (page...
Hello. Is it possible for a central device to retrieve the BDADDR( 6 byte array data ) of a past peripheral device by using the peer manager? ("past peripheral device" refers...
Does anyone know how the raw data message is structured to enable GATT Proxy? Here is a screenshot from the app. I know one byte is used to indicate whether to enable or disable...
Hi,
actually I developed a system based on an nRF24AP2 able to read data coming from different HRM ANT+ sensors and transmit them via WiFi using ESP8266 that is acting as...
I have clock drift issue, should I calibrate anything? I test this simple code to get 1second or 100ms signal both of them are inaccurate.
here is my code for 100ms; I tested...
I'm trying a new device based upon the nrf52810 and it won't run past sd_softdevice_enable - it goes to the assembler window and halts. The device does have a 32kHz xtal and...
Hello,
I was reading some SDK 15.3 code, there's something like this:
__STATIC_INLINE void pwr_mgmt_sleep_init(void) { #ifdef SOFTDEVICE_PRESENT ASSERT(current_int_priority_get...
Hi all, I'm developing nRF52840-DK to use it as an central device.
Base example is usbd_ble_uart: I'm going to communicate with peripheral device using BLE, and control...
We have a product that uses the nRF52840. We have seen that very rarely, unexpected resets happen with the reason being OFF. We have yet to encounter this issue in a lab setting...
I'm using the SPI manager to talk to an ILI9342 graphics IC. I need to toggle an IO line during a transaction or in between transfers. For the first byte the line will be...
