Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
Hi support Team,
Following are my Questions.
1. Please recommend me three development boards from Nordic. I would like to build the mesh Network.For example one will transmit...
I am seeing a number of issues, but since they appear to be different, I will use different threads.
Setup: have gone to ble_blinky example to keep things as simple as possible...
Hi, i am new to the nRF52840, i like the features it has and i want to create a board using it. In the datasheet it is said to have 2 ARM processors and i want to use it as...
About 3.7V Li-Po battery on spec., can we read adc value from the battery using p0.04(A1) without external voltage divider circuits? In fact, 3.7V battery outputs 4V ,seeing...
Hi,
I'm now planning to test BLE AoA using nRF52833 DK. For now the DK doesn't have antenna array, so I plan to use an addon board like below:
Is there any link or example...
How can I define paths in SES (Windows), like $SDK_PATH, for my project?
- if they are defined in macros, what is the syntax?
- is there a standard variable that has a...
HI there,
I wanted to use nrfx spi with nRF5 SDK 17.0, but it was removed. I checked that in nRF5 SDK 15.3 it should be available, but when I downloaded it the example is...
Hi Everyone,
Last two weeks I'm trying to make a Real time streaming custom service on PCA10056 DK. I have modified the ble_image_transfer code according to my requirement...
I'm testing the Zigbee CLI Agent example and try to read info from my Titan wall sensor. I can read almost all info, but not values, that are using float type.
How I can...
Hi everyone,
I have an issue when i am writing to flash sometimes i get a SOFTDEVICE assertion failed just after using the function fds_gc().
The structure i write...
Hi,
Similar to https://devzone.nordicsemi.com/f/nordic-q-a/45544/nrf9160-dk-psm-current-too-high-after-opening-and-closing-a-tcp-socket/260026#260026 , however they said...
I have been looking at the Mesh library for BLE communication and wonder how much work it would be for me to use the same library for a long range 2,4 GHz radio?
Is the...
Hi,
now we use SDK17 "ble_app_hids_keyboard" example, we found after the moble phone connected to the ble keyboard, if the ble keyboard power off and power on ,the phone...
I am trying to to do adc reading from external 9V Litum battery.
In the PS document, I know nRF52832 can read adc until VDD(3.7V ???).
Then, in my case, do I have to design...
Hi,
I use the timestamp log in SDK17, and I find the time will auto clean at about 1min6-7sec.
Below is the code init the log.
/**********************************...
